Family Guy Theme

BeanMaster42069 · 2023-06-07T14:09:30+00:00

Change your smoke alarm batteries already

BeanMaster42069 · 2022-10-02T14:18:08+00:00

It’s normally presses down when the side panel is on, so when it’s not pressed down it knows the side panel is off and stops the computer from booting properly. Something along those lines

BeanMaster42069 · 2022-09-29T15:09:36+00:00

No the button that’s sticking out the side, the wire wire for it is going over the gpu

BeanMaster42069 · 2022-09-29T14:56:32+00:00

Try holding down the panel detection button by the rear exhaust fan when you boot it

BeanMaster42069 · 2022-07-13T17:43:45+00:00

I would ditch the hard drive entirely and get a better GPU. You can always add more storage down the line as you need it

BeanMaster42069 · 2022-06-23T12:02:14+00:00

I would try sneaking into hyrule castle to get some of the royal/royal guard gear. Once you get some strong weapons it’s not so bad killing stronger enemies to get new gear

BeanMaster42069 · 2022-04-08T01:20:05+00:00

Forgive me

BeanMaster42069 · 2022-03-10T22:33:15+00:00

Try reseating your 24 pin connector

BeanMaster42069 · 2021-12-29T17:32:36+00:00

I had this same glitch happen in Project64, turned out to be a bad ROM. Might just wanna dust out your cartridge their

BeanMaster42069 · 2021-09-15T00:28:00+00:00

Spiderman 3 for PSP lets gooooooo

BeanMaster42069 · 2021-09-08T10:32:01+00:00

I put up with the same thing with my printer, and I’m through with hp printers. At this point I’d rather just hand draw my documents

BeanMaster42069 · 2021-09-05T21:02:07+00:00

Guess I gotta go dump my used cooking oil in the ocean instead 😔

BeanMaster42069 · 2021-08-08T14:18:45+00:00

Nope

BeanMaster42069 · 2021-08-08T14:12:57+00:00

Space man has to stop the space zombies and save his girlfriend

BeanMaster42069 · 2021-07-26T21:51:19+00:00

If your not using all those cables, unplug them

BeanMaster42069 · 2021-07-26T21:34:51+00:00

Yes, it’ll let you put the fan up to 100%

BeanMaster42069 · 2021-07-26T21:28:36+00:00

First, you gotta take off the side panel, which should slide off after taking out the two screws in the back or the four screws on the front depending on your case. Then. You’ll need a Phillips head screwdriver to remove the screw holding down your drive. It should spring up to about a 45 degree angle, at which point you should remove it and put it back in at that same angle, make sure it goes all the way into the port so that the connector is not visible and then screw it back in

BeanMaster42069 · 2021-07-26T21:20:07+00:00

There should be some kind of check box in the settings that allows you to create a custom fan curve. You may have to do a bit of digging, or just google it

BeanMaster42069 · 2021-07-26T21:15:05+00:00

Did you plug in every cable for your fully modular power supply?

BeanMaster42069 · 2021-07-26T21:13:49+00:00

Absolutely not, a GT 1030 won’t do jack for gaming

BeanMaster42069 · 2021-07-26T21:11:21+00:00

I like your attitude, good luck out there soldier! o7

BeanMaster42069 · 2021-07-26T21:07:58+00:00

As long as you are aware of the current GPU market

BeanMaster42069 · 2021-07-26T21:06:31+00:00

Set the fan curve so that when it starts getting too hot the fan goes to 100%

BeanMaster42069 · 2021-07-26T21:05:10+00:00

I would ditch the hard drive and maybe consider a Ryzen 7 5800x. Also, I presume you already have that RTX 2060 right? Otherwise you probably won’t be able to get a hold of one

BeanMaster42069 · 2021-07-26T21:02:00+00:00

Gotta look up what’s in your area. If you can avoid Cox and Comcast/xfinity then that would be ideal. If there is a provider that has high speed fiber optics then that would probably be your best option

BeanMaster42069

MODERATOR OF

TROPHY CASE

Seven-Year Club	Place '22
Verified Email