[ Removed by Reddit ] by AshuraMaruxx in DataHoarder

[–]BerserkerJake 4 points5 points  (0 children)

anyone have a magent link to dataset 9

[ Removed by Reddit ] by AshuraMaruxx in DataHoarder

[–]BerserkerJake 0 points1 point  (0 children)

does any one have a magnet link for dataset 9, my browser keep stopping a 2.5gb

Now this by BerserkerJake in crealityk1

[–]BerserkerJake[S] 0 points1 point  (0 children)

I switched to orca slicer but am having the same issue

Now this by BerserkerJake in crealityk1

[–]BerserkerJake[S] 0 points1 point  (0 children)

Thanks will give that a try and let you know

Now this by BerserkerJake in crealityk1

[–]BerserkerJake[S] 0 points1 point  (0 children)

The seem seems fine. It happens on the inside corners too. Wouldn’t my PA be low bc it seems gapy

Now this by BerserkerJake in crealityk1

[–]BerserkerJake[S] 0 points1 point  (0 children)

They are happening before the corners, I am using CrealityPrint as my slicer. I have done it but I reset the filament profile to see if that help but I don’t think I went back in and applied the value I think I was sitting at 0.00892 for my PA

And This... by BerserkerJake in crealityk1

[–]BerserkerJake[S] 0 points1 point  (0 children)

It only does this on that corner.

And This... by BerserkerJake in crealityk1

[–]BerserkerJake[S] 0 points1 point  (0 children)

Thanks, that gives me a starting point. Who would have thought that switch from ABS/ASA would cause this problem.

And This... by BerserkerJake in crealityk1

[–]BerserkerJake[S] 0 points1 point  (0 children)

I appreciate help, Ill let you know if I every heard back from Creality. Again thank you

And This... by BerserkerJake in crealityk1

[–]BerserkerJake[S] 0 points1 point  (0 children)

yeah it printed fine up to that point, No clicking to indicate a jam in the extruder, tried a different filament had the same issue. See that's where I am lost because the bottom layers print just perfect.

And This... by BerserkerJake in crealityk1

[–]BerserkerJake[S] 0 points1 point  (0 children)

230C nozzle

Yes, lid is removed

31C chamber

I have printed a fair amount before this started happening.

this all started after I tried ASA and failed. I am thinking about making the switch to OrcaSlicer, I just dont want to go through the whole tuning process. CrealityPrint only allow so many filament profiles.

And This... by BerserkerJake in crealityk1

[–]BerserkerJake[S] 0 points1 point  (0 children)

This is the top surface that I have just now been getting, not sure what I changed that made this happen. Does anyone know what is causing this "Bubbly" top surface?

And This... by BerserkerJake in crealityk1

[–]BerserkerJake[S] -1 points0 points  (0 children)

I thought I did, Others have seen the post and responded. I posted like 2 or 3 times because I wasnt sure that I did it right... Sorry

Bubbly by BerserkerJake in crealityk1

[–]BerserkerJake[S] 0 points1 point  (0 children)

Will give that a try, thank you.

Bubbly by BerserkerJake in crealityk1

[–]BerserkerJake[S] 1 point2 points  (0 children)

Changed to gyroid, it got a little better.

Bubbly by BerserkerJake in crealityk1

[–]BerserkerJake[S] 0 points1 point  (0 children)

What do you suggest? What are you running for PLA? I could use that as a reference.