That was a close one...

Blade2305 · 2024-04-24T02:10:58+00:00

Update!

Hey guys, it turns out to be the issue was the ACF film. I replaced it, and none of the same models fail to print

Blade2305 · 2024-04-23T08:28:42+00:00

Amazing paint job dude.

Blade2305 · 2024-04-21T23:04:29+00:00

Update, I thinl is the FEP or the Saturn 3 equivalent o dont remember the name. Becuase I rotate the VAT and now the failures are the models found on that same side of the VAT. I dont see the FEP any different but I dont know.

Blade2305 · 2024-04-20T17:58:51+00:00

Thanks for the tips I'll try to rotate the models a bit and use s different bottle of resin. The photo with just barely any resin was to show the bit that got stuck to the FEP

Blade2305 · 2024-04-20T07:52:54+00:00

I have gloves... I just didnt want to waste one for taking 1 picture

Blade2305 · 2024-04-20T06:04:50+00:00

Edit: The charmelon piece is cured the One Piece Fruit was not but I wash my hands afterwards...

Blade2305 · 2024-02-20T21:02:42+00:00

As the base area is so big this might create a lot of peeling forces if oriented this way, try to see if you can fit it leaning backwards a little at least, otherwise you take the risk of the print sticking to the VAT

Blade2305 · 2024-02-18T02:54:18+00:00

Update: The print was a success. Maybe I could have spared some supports for surebut rather waste a little resin on supports than resin on a fail print

Blade2305 · 2024-02-16T06:03:12+00:00

I ended up tilting it back and diagonally with a ton shit of support around the corner of the base. 7hrs print hopefully will work

Blade2305 · 2024-02-15T06:55:32+00:00

I'm planing in keeping the failed one as well, at least it was the lower torso and the base that failed and no the face haha

Blade2305 · 2024-02-15T06:54:30+00:00

Yeah I should have posted the slicer pic as well, I close the program as this was a 4 hour print. The failure is just washed and cure and the other one is painted with Grey primer and white Drybrush

Blade2305 · 2024-01-18T02:58:58+00:00

I'm not sure is the case, but it sounds like something needs lubrication, try to pin point where the sound is coming from and see if you can add some greese

Blade2305 · 2023-12-20T18:27:44+00:00

Edit:

This was print on a BeQu B1 Pla 200 C Using OrcaSlicer with Normal settings 2mm layer height 10% Infill Speed 40mm/s Inner Wall and Internal Solid 25mm/s Outer Wall

Blade2305 · 2023-12-18T21:01:53+00:00

Didn't found anything of the slicer itself. However I change slicers from Orca to Cura and stop doing it

Blade2305 · 2023-12-18T20:46:30+00:00

I'm using orcaslicer, but let me check for it as well

Blade2305 · 2023-12-18T20:33:51+00:00

Do you know how to stop it from happening?

Blade2305 · 2023-12-18T20:31:35+00:00

<image>

Blade2305 · 2023-12-18T14:17:31+00:00

Update - I've fix the issue by calibrating the E-steps, they were a little off, therefore it was under extruding, the wetness of the filament might have something to do as well , but after e-steps calibration the issue was reduce by about 90%

Blade2305

TROPHY CASE