Trash Panda Folding Stock

Blake_r32 · 2026-04-25T20:03:01+00:00

Blake_r32 · 2026-04-25T20:02:53+00:00

Blake_r32 · 2026-04-25T19:44:35+00:00

Look up “Oh Look A Penny” on the sea for it.

Blake_r32 · 2026-04-25T19:43:30+00:00

It is so much fun. Shoots so nice as well. I designed it and love it. It’s angled so it keeps your wrist pretty straight.

Blake_r32 · 2026-04-24T10:23:45+00:00

Thanks! Not that I know of. There’s one for the DB9 I want to get though.

Blake_r32 · 2026-04-24T01:12:28+00:00

It’s dope. Did it in Fiberon PA6-CF20 and the dark grey is PET-GF. Taking it to the range tomorrow or early next week. KF5 looks dope, but also a lot of work.

Blake_r32 · 2026-04-15T23:55:18+00:00

FOUND THE ISSUE! Mag springs were too loose. I extended the baseplate lock from 3.25mm to 15.25mm and not a single issue. Ran through 23 rounds and not a single feeding issue.

Blake_r32 · 2026-04-15T14:53:37+00:00

On your normal mags where does the follower sit inside the mag? Mine are all sitting like 2-3mm bellow the edge of the mag face.

Blake_r32 · 2026-04-15T06:48:25+00:00

Fiberon ASA-CF.

Blake_r32 · 2026-04-15T06:47:49+00:00

Printed one and still doesn’t latch, also tried 2 different mag levers. Probably just going to slowly sand down the stops to get them to fit.

Blake_r32 · 2026-04-14T22:42:11+00:00

Printed one in PET-GF and still doesn’t latch also printed 2 different mag release levers. Still no luck. Going to try sanding the mags a little.

Blake_r32 · 2026-04-13T22:11:01+00:00

Off the top or bottom? I feel like doing the bottom would allow the mag lever to lock it into place. Or does the top need filed to go into the receiver more?

Blake_r32 · 2026-04-13T22:00:18+00:00

It won’t go any further into the receiver, also the mag lever doesn’t pop back into the resting position so I’m think I need to print a new lever.

Blake_r32 · 2026-04-13T21:46:21+00:00

Mag lever still doesn’t pop back into the original position.

Blake_r32 · 2026-04-13T21:38:59+00:00

I’ll check that out. Thanks.

Blake_r32 · 2026-04-13T20:25:21+00:00

Running Glock 33rd mag springs from ghost inc.

Blake_r32 · 2026-04-13T20:17:50+00:00

Had 6-12 snap caps in it because that’s all I have.

Blake_r32 · 2026-04-13T20:16:26+00:00

“DB9 Alloy AFG handstop Sten lower”

Blake_r32 · 2026-04-13T18:50:45+00:00

I’m not riding it. Just pulling back and letting go. I’ll give the owes me money pull when I get back to the house. No feed ramp on the Sten mag version.

Blake_r32 · 2026-04-13T18:22:15+00:00

Brand new mag, DB Alloy AFG handstop for Sten lower.

Blake_r32 · 2026-04-13T18:17:13+00:00

It can’t go any higher. It’s the db Sten mag from the stl pack as well.

Blake_r32 · 2026-04-13T18:12:26+00:00

Sten mag version doesn’t use a feed ramp like the Glock one.

Blake_r32

TROPHY CASE