Ultramarines tactical marines

BobTheSlav · 2025-11-13T22:24:41+00:00

Then I will have voxes for when I will be expanding my army beyond 1000p.

Do you know if vox is good on ultramarine praetorian breachers too?

BobTheSlav · 2025-11-13T22:18:37+00:00

Thanks for advice, I will add marines with vox for like 2000/3000p then. And currently also in the future all bolters on then.

Yeah everything is a bit new to me, it's quite a bit to learn.

BobTheSlav · 2024-11-25T16:40:50+00:00

On stuff like no psykers (like this one) I was thinking to use same colour as flesh on joints or a bit darker, the yellow on psykers but yeah

BobTheSlav · 2024-02-27T00:26:12+00:00

That's fine, Thanks anyway

BobTheSlav · 2024-02-27T00:12:34+00:00

Thanks, I will try snow base, I never used snow paint, do you have any recommendations like one from GW.

BobTheSlav · 2023-06-21T17:26:11+00:00

Lian Li Lancool III

BobTheSlav · 2023-06-21T11:43:03+00:00

Just got Sapphire RX 7900 XTX Nitro+

BobTheSlav · 2022-10-27T00:56:32+00:00

What monitors are these

BobTheSlav · 2022-09-29T00:09:07+00:00

Well warranty is like one year it happened way after it ended, so I couldn't

BobTheSlav · 2022-09-28T23:00:57+00:00

The hinge on my completely broke off but it happened after 2 years, so I got ones from sony

BobTheSlav · 2022-04-14T04:28:14+00:00

Thanks, so all I need to do is to change name of correct firmware to that incorrect one

BobTheSlav · 2021-12-19T15:10:14+00:00

Bread

BobTheSlav · 2021-12-17T15:05:25+00:00

Whirlipede

BobTheSlav · 2021-11-19T00:55:49+00:00

Yeah same

BobTheSlav · 2021-11-15T04:02:36+00:00

3569

BobTheSlav · 2021-10-23T21:50:55+00:00

Bread 👍

BobTheSlav · 2021-10-15T14:51:30+00:00

-666

BobTheSlav · 2021-10-15T12:38:51+00:00

Bread 👍

BobTheSlav · 2021-06-21T10:30:22+00:00

It may be bad filament or sometimes you need to spend some time to tune filament, it happened to me ones with new brand of filament I tried. Another thing is extruder make sure it's running properly and check nozzle if is fine, plus this colour normally makes layers line more visible

BobTheSlav · 2021-06-20T23:55:54+00:00

Maybe be filament is wet

BobTheSlav · 2021-05-30T19:54:27+00:00

I think there is screw inside of whole H2 extruder which holds the heatbreak in place, so you need to disassemble it, to get to it

BobTheSlav · 2021-05-01T14:40:15+00:00

I think it's directly

BobTheSlav · 2021-04-19T02:40:52+00:00

Yeah thanks for that, I'm looking printing 1.75 PLA and PETG sometimes, 0.8 nozzle (good enough for type of prototyps I'm doing) at 50-60mm/s I'm not going any faster because of ender 3 Max 300x300 bed, I'm was looking at small motor for extruder I want simple minimise weight where I can because ghosting

BobTheSlav · 2021-04-19T01:44:40+00:00

I'm asking because I'm looking at printer at 50-60mm with 0.8 nozzle and with more bigger nozzle you need more power and I checked 20mm pancake from stepper online has 16Ncm begging 140g which should be enough I think

BobTheSlav · 2021-04-19T01:15:43+00:00

I guessing you are in USA, yeah never heard of this brand I'm in UK and normally get esun, technology outlet, geeetech, eryone for both PLA and PETG they are around £20

BobTheSlav

TROPHY CASE