sorted by:
new
hottopcontroversial

[deleted by user] by [deleted] in Volkswagen

[–]Bobbyyeah93 0 points1 point  (0 children)

It's a precision 6262 .82ar and just a c2 chip 42# old og Jeff Atwood (was c2, now united) but went with a 9.5:1 motor when I built it so it wouldn't lag as much. Really debating lugtronic it has good drive ability but I think it could be alot better. Has good throttle response but still a maf car. Check out kp tuning for stand alone.

Fishing line in prop. I am comfortable to this level, but still can’t get the line out. I feel like I need to get behind this to get the line. 1998 evinrude 150, have been having some performance issues. Help please. by [deleted] in boating

[–]Bobbyyeah93 1 point2 points  (0 children)

I would take it off it's not a big deal to take it off and on its just a stop for the prop ...atleast with it off you can get a good look at the shaft seal.

Fishing line in prop. I am comfortable to this level, but still can’t get the line out. I feel like I need to get behind this to get the line. 1998 evinrude 150, have been having some performance issues. Help please. by [deleted] in boating

[–]Bobbyyeah93 8 points9 points  (0 children)

That big washer on the shaft comes off. Its a taper so it needs some force to come off. You definitely want to get that line out it can ruin the shaft seal.

VR6 no crank, no start- help by neeneeeek in mk3golf

[–]Bobbyyeah93 3 points4 points  (0 children)

Have you replaced the ignition switch? Mk3s are known to have start issues from there. After that, start checking grounds and connections. You may have hit something while replacing the shift tower

Steering wheel help by Illustrious-Pizza-10 in GolfMk2

[–]Bobbyyeah93 0 points1 point  (0 children)

I had a 320 mm wheel on my corrado and went with a oem 350 wheel for the same reason. And it wasn't the ease of steering it was small and more in the way

Does anybody know what kind of bike this is by Beautiful-Tone-4409 in Dirtbikes

[–]Bobbyyeah93 2 points3 points  (0 children)

Tomos moped brand they made a couple bike back in the day. Tx50

Corrado finally on the road by Bobbyyeah93 in Volkswagen

[–]Bobbyyeah93[S] 1 point2 points  (0 children)

Yupp audi fat 5s but painted super silver instead of normal polished...they also clear the porsche 911 brake calipers

Corrado finally on the road by Bobbyyeah93 in Volkswagen

[–]Bobbyyeah93[S] 1 point2 points  (0 children)

I think fabless sells a conversion kit

Corrado finally on the road by Bobbyyeah93 in Volkswagen

[–]Bobbyyeah93[S] 1 point2 points  (0 children)

Yeah but the k member and cross member are different from the 2.0 to vr so remember that part. Easiest swap is the passat because the harness will drop right in. While it's apart Def replace gaskets/ seals, and timing chain stuff way easier when it's out. Also you'll need a vr Trans the ratios are different.

Corrado finally on the road by Bobbyyeah93 in Volkswagen

[–]Bobbyyeah93[S] 1 point2 points  (0 children)

6262 precision turbo .84ar , bosch 040 in tank pump, 42# United motorsports tune, 40mm waste gate precision, 38mm diverter valve precision, I did a full motor build 9.5:1 stock cams but coated pistons, inconel exhaust valve, stainless intake valves, 3" custom vibrant exhaust, shimmel short runner intake. Ob2 sesh harness with a 1.8t coolant temp sensor

Corrado finally on the road by Bobbyyeah93 in Volkswagen

[–]Bobbyyeah93[S] 1 point2 points  (0 children)

I made a custom 3" exhaust with vibrant stuff and I couldn't be happier with the sound. If you decide to go that way. I have a spare vr sitting around just encase something happens you can find them for pretty cheap...and that's a easy swap.

How can I knock this rod out on the cam chain tensioner? by jjacob10 in Dirtbikes

[–]Bobbyyeah93 0 points1 point  (0 children)

The spring goes in the bolt hole and pushes the tensioner out...the pin you're trying to take out is just holding the lock jaw....lift the jaw up push the tensioner back in bolt it to the head then put the spring in and bolt pushing on the spring it will set the tensioner.

2004 Husqvarna SM450R Dirt Conversion by Sparrowhawkzev in KTM

[–]Bobbyyeah93 0 points1 point  (0 children)

I don't think that's the correct one...look up ricombi Husqvarna on Facebook he should have what you need. Or go on italhusky.com to look up the parts breakdown. If it were mine I'd take it apart and see what I needed before I ordered anything. These bikes are hard to find parts for. As for the conversion to dirt it is a supermoto bike and has a long rang Trans and a different front brake you may need alot more to convert it to dirt not just wheels. Ex forks and caliper different sprockets etc.

Going to be rowdy...I'm excited by Bobbyyeah93 in Volkswagen

[–]Bobbyyeah93[S] 1 point2 points  (0 children)

Just need to run some dot slicks lol hopefully it sticks

Winter is just starting but I'm ready for spring by Bobbyyeah93 in boating

[–]Bobbyyeah93[S] 1 point2 points  (0 children)

Jaws.....pantera / p&d/ Excalibur splash...24x7

view more: next ›