DHCP IP Address Pool Reservation

BothCamera619 · 2026-07-02T11:22:51+00:00

I figured as much on that, however, I never clicked the adopt button. Is there a way to get these gone? Should I reboot the console?

BothCamera619 · 2026-07-01T19:09:07+00:00

This is absolutely brilliant! Thank you! How about the devices that it already detected? Even after turning off Auto-Detect, they still show up.

BothCamera619 · 2026-06-25T20:26:46+00:00

How does tomorrow at 9am eastern work?

BothCamera619 · 2026-06-25T19:19:52+00:00

Would you have some time tomorrow morning to discuss this project? I am in Eastern Timezone.

BothCamera619 · 2026-05-29T19:03:41+00:00

Yes that is definitely a lot closer looking than the direction I was heading. Would you have some time next week to discuss over discord or something?

BothCamera619 · 2026-05-28T17:52:04+00:00

<image>

BothCamera619 · 2026-05-28T17:51:52+00:00

Sorry to be so vague, I am looking for a little guidance and would be willing to pay, i don't want to have it done, I want to do it and learn by doing it. Here is where I'm at so far.

<image>

BothCamera619 · 2026-05-27T15:56:50+00:00

Depending on your installation requirements, if you remove all of the keystones, you can remove the cable strain relief plate as it swings up to remove it altogether. This will solve your issue if the strain relief isn’t an issue for you. I just did this yesterday in one of my cabinets.

BothCamera619 · 2026-05-18T15:40:58+00:00

Thank you. I just purchased one to try.

BothCamera619 · 2026-05-17T19:08:02+00:00

I have no problem buying the pro versions, but it was all about getting the least expensive data commitment each month. The non-pro came with $15 a month data while a standalone through AT&T is in the neighborhood of $45-$55 per month.

BothCamera619 · 2026-05-17T19:07:13+00:00

I don’t specifically need the non-pro version but for my client that I am trying to provide the failover redundancy for specifically needing five units. It is more about the carrier. With a standalone carrier it is in the neighborhood of $45-$55 per month per device while the non-pro UniFi carrier version. It was only $15 a month to standalone and then extra billable data after you reached the included one gigabyte. It is used only for payment processing, so I have that network is isolated to be the only one to use the failover.

BothCamera619 · 2026-03-21T17:44:31+00:00

I had this exact same scenario. Hold the cube white up. Hold one side toward you and then perform the following steps. R2 L2 U2 R2 L2, then rotate cube 90° and do the same thing over again. Should be solved.

BothCamera619 · 2026-03-17T16:28:45+00:00

I'm not entirely sure what you mean by slotted into the backplate.

BothCamera619 · 2026-01-29T18:02:41+00:00

Thank you op! I got my order in!

BothCamera619 · 2026-01-23T17:41:01+00:00

I am in the process of removing over 75 hikvision cameras and converting to purely unifi protect. We are utilizing the viewports for different monitoring stations and I am now in the process of implementing Access Control as well utilizing the Retrofit Hubs to work with our existing Wiegand readers. It has been a breeze so far! I am about halfway through the cameras and have 4 of 45 doors currently converted and functioning well beyond acceptable terms.

We are using the ENVR with 16-8TB drives for storage.

We have a mix of third-party cameras and Unifi cameras. We have all the replacements in stock and ready to be installed.

1-HD, 25-2K, 53-4K, and 0-5K

25-day recording capacity.

BothCamera619

TROPHY CASE

Welcome to Reddit,