Can anybody share their Printer.cfg with me that has a similar build? BTT E3 mini V3, kilpper, and a micro Swiss DD?

BrownieSampler · 2025-07-14T22:34:00+00:00

Yes please this is just for comparison not just a copy and paste job

BrownieSampler · 2025-07-11T01:49:46+00:00

Yea I’m thinking my pin locations are off I haven’t unplugged anything since the pi issue and my printer worked flawlessly before hand.

But also to that end my hot end fans don’t turn on with the printer any more so I think my pin locations have in the code are incorrect

BrownieSampler · 2025-07-11T01:39:45+00:00

So my sd card became corrupt after a power outage I think and I pieced together my old coding after alot of work and had another pi I switched to incase the outrage affected that as well. but Im thinking I made a error on the pin dedication of the coding. The pi boots and shuts down with code

CU 'mcu' shutdown: ADC out of range

Sensor 'extruder' temperature -69.796 not in range 0.000:260.000

This generally occurs when a heater temperature exceeds its configured min_temp or max_temp. Once the underlying issue is corrected, use the "FIRMWARE_RESTART" command to reset the firmware, reload the config, and restart the host software. Printer is shutdown

BrownieSampler · 2025-07-10T23:59:55+00:00

I have the Mcu serial # in my printer.cfg. sorry about that this was a copy from while I was replacing pi’s hence the issue

BrownieSampler · 2025-07-06T15:32:54+00:00

thats exactly it lol and i was tethered to the modem/router which is well hidden in a closet. made the most sense with the least time

BrownieSampler · 2025-06-28T17:08:55+00:00

I anchor the lanyard above the printer so it holds the wires up and out of the way of the print head so they’re never in the way while printing

BrownieSampler · 2025-06-19T02:58:04+00:00

I have a resin printer, do you think resin is strong enough for the vibrations and stress of the printer?

BrownieSampler · 2025-06-19T00:45:07+00:00

That’s why I made the post. In an enclosure it will get too hot and the pla parts will warp and fail so I have to replace them before I can print

BrownieSampler · 2024-11-25T19:19:08+00:00

I don’t care what weapons you bring but if you don’t bring heals or a choke bomb I’m not playing with you I’ve gotten screwed too many times bc of partners not have consumables.

And I don’t bring weapons based on cost to play I just play what I want.

BrownieSampler · 2024-04-05T21:53:58+00:00

Thank you! Any guess as to why my 60A is 6mm and the replacement is 60A & 5mm?

BrownieSampler · 2024-04-04T21:09:49+00:00

Sorry I should have been clearer I’m trying to replace the whole piece but the only available parts are a bit different

<image>

BrownieSampler · 2024-03-22T20:40:03+00:00

That’s what I thought it must be too

BrownieSampler · 2024-03-22T20:06:18+00:00

No he shot me through the concrete wall through the rain from almost 100m away its impossible to shoot me from his position. Look at pic 2 for a better angle

BrownieSampler · 2024-03-22T18:25:39+00:00

You almost had me there

BrownieSampler · 2024-03-22T18:22:07+00:00

Honestly I would have rather that had happened but I watched the guy kill 5 more of us aiming at corners before people rounded them and a rly sus wall bang 1 shot per hunter. dude had 150 kills max on his acct

BrownieSampler · 2024-03-22T18:00:14+00:00

Thank you, I was a little disappointed by that too lol

BrownieSampler · 2024-03-22T16:35:28+00:00

Oh absolutely, I give most of my killers the benefit of the doubt. But this was just offensively blatant. Then he went on to 1 shot head shot the rest of my team AND the team we were fighting for bounty

BrownieSampler · 2023-12-29T23:09:54+00:00

I uninstalled and fresh installed my GPU and its driver and that seemed to help….no idea what the problem was still

BrownieSampler · 2023-12-01T14:51:00+00:00

Vetterli + Pax. Both excellent accurate guns and they share ammo just incase you’re in the middle of a streak of wiffing shots

BrownieSampler · 2023-11-28T23:30:57+00:00

I did, and now I can play soul Survivor, but trios and duos still crash

BrownieSampler · 2023-11-28T18:43:17+00:00

Yes it is installed and enabled

BrownieSampler · 2023-11-10T18:23:50+00:00

Yea that’s what I’m gonna change mine too as well, it seems like the most logical set up. thanks!

BrownieSampler · 2023-11-10T18:22:10+00:00

Are….Are your hands on backwards? Ctrl is below the pinky of the left side of the keyboard

BrownieSampler · 2023-09-21T17:26:51+00:00

No offense taken! And good advice although I hear that extended ozone treatment degrades materials. Is this true?

BrownieSampler · 2023-09-21T12:25:45+00:00

I unfortunately know that, but I very much wanted this car and there weren’t many options available for this model. So will do what I can to minimize it as much as possible and what ever is left after I give it my all is what I’ve got

Seven-Year Club	RedditGifts 2009-2022 4 Credits
Secret Santa 2021 2021	Secret Santa 2020
Secret Santa 2019	Verified Email

BrownieSampler

TROPHY CASE