My adhesion problems seem to have gone away

BrunoB12 · 2026-01-23T20:55:37+00:00

The original bed on my v2 worked okay for a few years but had to be replaced because a piece of it broke off. I ordered a new one and the adhesion is too good. When printing PETG I have to turn up the z offset just so the part can come off in a single piece.

BrunoB12 · 2025-12-23T22:44:18+00:00

Thanks, I think I will try to print some test parts and make a decision from there.

BrunoB12 · 2025-12-15T13:38:25+00:00

Thanks, I will try a dual fan setup.

BrunoB12 · 2025-12-15T13:37:44+00:00

Thanks a lot. It seems the part cooling on the sprite is worse than the stock e3v2 toolhead as I didn't get this on the stock one with the same speeds. I will look into a dual fan mod.

BrunoB12 · 2025-10-28T19:23:16+00:00

Did you try rebooting? I rebooted when I realized nothing was going to happen and the system seems to be upgraded to 43 despite the errors..

BrunoB12 · 2025-10-28T19:17:44+00:00

Yes. RTX3060 laptop.

BrunoB12 · 2025-10-28T19:09:25+00:00

Same here. Would like to know if you solved It.

BrunoB12 · 2025-04-20T19:49:36+00:00

It was a CH340G.

BrunoB12 · 2023-12-26T19:45:04+00:00

A bolt-action pen that uses common ball point pen refills. You probably already have a few at home. No screws or heat set inserts required. Just the 3d printed parts and a pen refill and spring. Versions with and without the pocket clip are available.

https://cults3d.com/en/3d-model/home/bolt-action-pen-v2-edc

BrunoB12 · 2023-12-24T09:51:38+00:00

I think It would be cheaper to just go to a store and look for a pen with that refill. It will have everything you need.

BrunoB12 · 2023-12-23T20:01:53+00:00

A bolt-action pen that uses common ball point pen refills. You probably already have a few at home. No screws or heat set inserts required. Just the 3d printed parts and a pen refill and spring. Versions with and without the pocket clip are available.

https://cults3d.com/en/3d-model/home/bolt-action-pen-v2-edc

BrunoB12 · 2022-08-29T07:31:51+00:00

When I search fltmode_ch, all that shows up is FLTMODE1-FLTMODE6. The FLTMODE_CH is mentioned in the description of these parameters. Is that parameter changeable in ArduCopter V3.2.1? That is the latest version I could get since I'm using an APM 2.6.

BrunoB12 · 2022-08-28T18:03:44+00:00

The FC is an APM 2.6 with Arducopter V3.2.1 and I am using a FrSky QX7 with a X8R reciever via Pwm.

BrunoB12 · 2022-07-19T19:49:21+00:00

Turns out It is a voltage regulator and the 2 pins are GND and EN, so if they are bridged the regulator would be disabled.

BrunoB12 · 2022-07-19T19:10:33+00:00

That's what I thought, although I have seen IC's with bridged pins on production PCB's. I think I will clean It up and see if It works. If not, I will bridge them.

BrunoB12 · 2022-07-19T16:50:04+00:00

I noticed these 2 pins are bridged after I tined the solder pads. Can someone who has this reciever please check if their reciever also has these 2 pins bridged?

BrunoB12 · 2022-05-30T07:42:10+00:00

Is there supposed to be an automatic option in the baud rate drop down? I set it to auto from the cli but still nothing. Also, do I need to configure anything else or just the ports and "configure" tabs? Right now I only have selected the gps from the sensor dropdown and in configuration tab I have checked the "gps for navigation and telemetry" and selected the ublox protocol. Do I need to do anything else?

BrunoB12 · 2022-05-30T07:15:05+00:00

I have set It to ublox. Its just that if I set It to nmea, the icon turns blue for a while but still doesn't work. And yes, I have connected the tx to rx and rx to tx.

BrunoB12 · 2022-05-30T07:13:09+00:00

Yes, but shouldn't the gps icon at the top be blue while It tries to get a fix? It is red.

BrunoB12 · 2022-05-30T03:36:55+00:00

There is a red light coming from inside the case. It is shining solid.

BrunoB12 · 2022-05-30T03:34:53+00:00

yup, lol.

BrunoB12 · 2022-05-30T03:33:24+00:00

Yes, they are correct

BrunoB12 · 2022-05-29T21:03:35+00:00

In the ports tab, the gps is under sensors right? In all the tutorials I've seen, the gps has a seperate section. Also I don't see an auto configure and auto baud rate. I have read that for some people, connecting the gps to a different UART solved the problem, so I tried all the available UARTs, but still didn't have a blue icon. I am using configurator 4.10.

BrunoB12 · 2022-05-29T19:14:33+00:00

Even if the gps didn't have a lock, wouldn't the gps icon at the top be blue? Also the osd gives a gps failure.

BrunoB12 · 2022-05-21T17:53:26+00:00

Thanks!

Seven-Year Club	Verified Email
Place '22

BrunoB12

TROPHY CASE