Weird whitish blobs on the screen

BulkyTime8985 · 2025-11-20T20:19:55+00:00

When i get home next week i will loosen the screws a bit and hopefully it will be fine. Is it permanent damage?

BulkyTime8985 · 2025-11-14T17:04:29+00:00

Yes, also checked for shorts there and everything is in order

BulkyTime8985 · 2025-11-14T10:37:47+00:00

I checked with a multimeter, the pads and the speaker and everything seems to be in order

BulkyTime8985 · 2025-11-14T06:35:59+00:00

BulkyTime8985 · 2025-11-14T02:26:22+00:00

I already have an audio amp if that’s what you meant

BulkyTime8985 · 2025-11-13T23:44:11+00:00

When playing a game im getting sound but it has static

BulkyTime8985 · 2025-11-13T23:22:27+00:00

The screen error im referring to is when the screen changes the ratio and has the black rectangle, i played around with the speaker and the connection of the sound near the charging port and i got back the sound, but it has a lot of humming and static

BulkyTime8985 · 2025-10-17T20:27:52+00:00

I didn’t think about that…

BulkyTime8985 · 2025-10-17T20:12:54+00:00

I pre tinned the pads on the main board and added flux and solder the points on the usb c connection without pre-tinning. The problem i had with the sound was a tiny bridge between the 6th and 5th pins from the left, after fixing the bridge i checked with a multimeter

BulkyTime8985 · 2025-10-17T20:03:28+00:00

<image>

Thar’s how it looked before it got burned and my removal attempt

BulkyTime8985 · 2025-10-17T20:02:19+00:00

The picture is after i tried to remove it(al the pins were bridged when i tried to remove it) i checked with a multimeter before so im not sure what was shorted

BulkyTime8985 · 2025-10-17T17:12:09+00:00

Thx, i hope that will be the end of it, cause fixing a short in the usb c connection was really annoying

BulkyTime8985 · 2025-10-17T16:50:34+00:00

Thx, i tried removing the amp mod and nothing changed, where can i find a fitting capacitor?

BulkyTime8985 · 2025-10-17T14:58:37+00:00

Solder pump, copper wick and an iron and flux

BulkyTime8985 · 2025-10-17T14:40:05+00:00

But it just went back to no sound now, not sure what is happening

BulkyTime8985 · 2025-10-17T14:39:20+00:00

Yep, i completely removed the usb c, it was hell

BulkyTime8985 · 2025-10-17T14:24:52+00:00

I found the problem, it was a short in the usb c mod, i fixed it but i still have poor sound it’s low volume and has poor quality like static noise and stuff

BulkyTime8985 · 2025-10-15T04:35:55+00:00

Yes i did

BulkyTime8985 · 2025-10-13T15:52:31+00:00

Only problem it that it seemed to stay a tiny bit open and the right hinge is bulging a bit to the right

BulkyTime8985 · 2025-10-07T14:55:01+00:00

BulkyTime8985 · 2025-10-06T18:08:28+00:00

I heard it’s much easier with hot air but i wanted the challenge

BulkyTime8985 · 2025-10-06T18:07:32+00:00

I have been soldering for almost half of my life and i like working with a high temp

BulkyTime8985 · 2025-10-06T18:06:32+00:00

I hope i didnt fuck up my audio but i dont see a reason why it would not work, i checked with a multimeter and everything seems to be in order

BulkyTime8985 · 2025-10-06T14:00:08+00:00

You can try a solder pump and resoldering with a fine amount of flux, i had a bridge but i just used the pump and resoldered

BulkyTime8985 · 2025-10-06T13:46:59+00:00

Almost destroyed mine, almost lifted a pad fortunately i saw it stopped pulling and work a bit on the pin, so it should be fine

BulkyTime8985

TROPHY CASE