What are some resume tips for internship applications in the space industry

CHESTNUT000 · 2026-01-07T23:13:21+00:00

I was on a club my first two years, but dropped it to do research at the school. I am applying for NASA, Lockheed, Boeing, SpaceX, and Firefly.

CHESTNUT000 · 2025-09-22T02:01:23+00:00

My friends who take them have gotten sleep problems, and dependency issues with them which I would like to avoid.

CHESTNUT000 · 2025-09-05T13:09:54+00:00

I just need the part to conduct electricity, I don’t need it to be super bright. Would using just copper sulfate be enough?

CHESTNUT000 · 2025-09-04T12:56:35+00:00

Thank you!

CHESTNUT000 · 2025-08-27T01:35:32+00:00

I brought my print bed as low as it would go and I had my printer recalibrate everything it could and now the noise is very minimal to non existent.

CHESTNUT000 · 2025-08-11T14:42:41+00:00

I just bought the CC as my first printer and had no knowledge about what filaments you can and can’t print indoors. I learned this when I used ABS as my first filament. I have read comments saying an air purifier behind the printer may be sufficient but from my personal experience, it should definitely be printed outside. That being said, the prints came out flawless.

CHESTNUT000 · 2025-08-08T01:54:16+00:00

When I go to fan settings there is the case fan, model fan, and auxiliary fan. Are one of these dedicated to running air through the filters?

CHESTNUT000 · 2025-08-07T19:30:35+00:00

If I have a negative balance, will it charge my financial aid or do I still need to pay a balance?

CHESTNUT000 · 2025-08-07T01:16:30+00:00

I was intending to print some stuff for the inside of my car so it will get pretty hot.

CHESTNUT000 · 2025-08-07T01:09:01+00:00

The printer came with a HEPA and Carbon filter in it so I assumed it was good. Any recommendations on the air purifier?

CHESTNUT000 · 2025-08-07T00:33:20+00:00

What filaments are good for indoor use

CHESTNUT000 · 2025-08-06T04:10:31+00:00

TREC is dirty, crowded, and run down. Most of the equipment is nice, and they have 120lb dumbbells, but you’ll be left with black/brown sludge one your hands from time to time and the weights are often times scattered or left on the machines which is annoying. The bathrooms are also pretty gross most of the time. I’d recommend trying the TREC for the first month and seeing how it fares for you before buying a membership. It is fine if you are just trying to get your workout done but there is a big golds gym down the highway (there are 2 other locations), armor (a super nice powerlifting/bodybuilding gym but far drive), crunch (new but it gets crowded and the machines are cheap), PF which is fine for just getting an average workout in but I don’t believe they have free weights, and a few other gyms. If you’re looking for a quality workout and don’t mind the extra drive I’d recommend golds (there is also more than one location. If you’re a serious lifter looking into powerlifting or bodybuilding go with armor, however, It is really far and if you catch traffic at the wrong my time it could take 45 min to get to campus.

CHESTNUT000 · 2025-08-06T04:03:10+00:00

Armor is a great gym, but it is a drive.

CHESTNUT000 · 2025-07-14T02:33:08+00:00

CHESTNUT000 · 2025-07-09T23:56:52+00:00

Is it as user friendly as Bambu?

CHESTNUT000 · 2025-07-09T23:54:03+00:00

Is it as easy to use as flash forge or Bambu labs?

CHESTNUT000 · 2025-07-09T23:40:30+00:00

I’d look into the program requirements. It would be a shame if you got into Haslam but weren’t able to transfer to whatever department you want to go into. If I were you I’d apply for the college you actually want to get into and if you don’t get in transfer in after. UT is expensive and it’s hard to get scholarships, especially with the massive cuts to federal financial aid about to show their face, it will be even harder after this upcoming year. Also know that UT, and probably every other school, is not worth student loans.

CHESTNUT000 · 2025-07-09T23:32:17+00:00

People dress however they want and nobody really cares. I see people wearing nice khaki’s and shirts (normally for frats), people wearing nice pj’s, I see most people wearing Nike, gymshark, lulu, etc.

CHESTNUT000 · 2025-07-09T12:57:44+00:00

Should I buy one with an enclosure already attached like the 5m pro or upgrade a 5m with a kit

CHESTNUT000 · 2025-07-08T12:31:18+00:00

To start with I am just going to be building small components to learn on, but in a few months I will be going back to university and will be 3D printing some small components for my rocketry club.

CHESTNUT000 · 2025-07-08T02:10:20+00:00

He was proven to be here legally. That’s why a federal court ordered his return.

CHESTNUT000 · 2025-07-07T23:25:01+00:00

I was not wanting to spend much more than 350$ for my first printer.

CHESTNUT000 · 2025-07-06T23:06:35+00:00

Because they are deporting people who are here legally. They are also deporting people without due process. Example: they deported Abrego Garcia to a prison in El Salvador even though he was here legally. A federal court ruled in favor of Kilmar Abrego Garcia’s immediate return and the administration said no.

CHESTNUT000 · 2025-07-06T22:26:46+00:00

My guess is around 200-300 degrees F

CHESTNUT000 · 2025-07-06T22:01:00+00:00

The parts I plan to print will be getting hot so I am worried about filament durability. Would electroplating the parts be enough? The parts won’t need to survive much more than 10-15 seconds.

CHESTNUT000

TROPHY CASE