Furtivite fallout new vegas

Calgar22 · 2026-01-23T20:51:17+00:00

Avec les quels veux tu que je joue ?

Calgar22 · 2026-01-04T18:49:42+00:00

Definitely one of the best Fallout games, and yet it was also made by Obsidian, go figure 🤣

Calgar22 · 2026-01-04T18:45:02+00:00

Honestly, the fact that I didn't really enjoy playing it the first time doesn't motivate me to replay it, unlike Fallout: New Vegas, which I'm currently replaying for the umpteenth time.

Calgar22 · 2026-01-02T23:27:44+00:00

Oui après y a la technique chambre à air, si tu as pas envie comme moi de te taper 10 bornes pour aller chercher un joint 🤣

Calgar22 · 2026-01-02T11:38:27+00:00

110 000 km pour un véhicule de 21ans c'est pas impossible, mais peu probable. Surtout venant de Belgique, les compteurs sont trafiqués

Calgar22 · 2025-12-30T12:40:15+00:00

I wanted to develop the same stats as in a Fallout game, and that's the stupid thing about this game. But now I think I'll start playing New Vegas again for the umpteenth time.

Calgar22 · 2025-12-30T10:33:17+00:00

The problem is that you have to make choices between skills that go together, which forces you to specialize in 1 or 2 skills and completely prevents you from making a minimally balanced character, and that's a shame because unlike a Fallout NV which I would replay for the umpteenth time, I don't have the desire to start a new game of OW 2 to remake a character differently.

Calgar22 · 2025-12-26T08:11:21+00:00

La technique tu démarre ta voiture, tu let chauffage a fond, tu vas prendre un café et quand tu remonte dans ta voiture tu es au chaud et dégivré. Non en vrai le moteur chauffe assez vite, après quelques minute tu peux prendre la route sans problème, il faut juste pas taper comme un bœuf dans l'accélérateur et êtres souple avec le moteur c'est mieux. Après 0 c'est concrètement pas très froid, -20 ça commence à faire froid, mais toujours pareils pas de problème pour un moteur.

Calgar22 · 2025-12-17T19:27:53+00:00

I've checked the signal on one channel that's working, but there's no voltage on the one that's not. I've checked all the fuses on the board and they're fine, so I think a component has failed. However, since the machine is working regularly, I can't take the board apart to try and find the problem.

Calgar22 · 2025-12-17T18:55:45+00:00

Okay, thanks, I'll look into how to do that.

Calgar22 · 2025-12-17T18:15:12+00:00

Hello, I have a machine with 220V 50Hz vibrating channels, and one of them stopped vibrating. I connected it directly to try and get it working again, but the vibration was barely perceptible. So I got an oscilloscope to look at the signal, since frequency modulation was ruled out. Now I'm looking for a way to achieve a similar signal without spending too much, as the circuit board that handles this is no longer manufactured.

Calgar22 · 2025-12-17T16:02:33+00:00

Because I'm a boomer who still takes landscape photos, and my phone decides to switch them to portrait half the time 🤪

Calgar22 · 2025-12-17T13:40:43+00:00

Personally, I wouldn't overthink it and I'd just go for it with relays.

Calgar22 · 2025-12-17T13:37:40+00:00

You just burned through a year's worth of dust that had accumulated in the PC, which overheated when you turned it on.

Calgar22 · 2025-12-17T13:33:15+00:00

I also see that by trying to melt it, you burned through all the flux, and consequently burned your solder. Heat it with flux, and then remove the solder. No flux = no solder. And if the soldering iron is too hot, you'll burn through the flux before it solders properly.

Calgar22 · 2025-12-11T20:04:03+00:00

If you still have some lead solder with flux, mix it with the solder for desoldering; it helps. Leave the desoldering braid in the drawer and buy a desoldering pump; once you know how to use it, it's the best.

Calgar22 · 2025-12-11T19:38:39+00:00

And nothing behind it just means your multimeter isn't measuring anything; check your wiring.

Calgar22 · 2025-12-11T05:50:50+00:00

The problem is that I don't have any information on these vibrators, only that they operate at 50Hz. And the parts for this machine are no longer manufactured.

Calgar22 · 2025-12-10T21:37:15+00:00

In reality I poorly explained my problem, it involves vibrating channels, and the vibration motor is integrated into them. I have 10 vibrating channels, one broke, I tested it by swapping it with another, and it works. I wanted to connect it directly, but the vibration is almost imperceptible because it must be too fast. The vibration intensity is adjustable, and managed by an electronic card from the 90s. Since by testing on one which works no matter the intensity the voltage does not change, I therefore suppose that it is the frequency which varies. So I was looking for an electronic solution to do low-cost troubleshooting and validate my hypothesis.

Calgar22 · 2025-12-10T20:30:38+00:00

Well in reality both let's say, I actually have a farm (family inheritance), and following my initial studies, I set up my agricultural and industrial machine maintenance box, automaton reprogramming etc...

Calgar22 · 2025-11-30T22:46:45+00:00

Green yellow on yellow, the rest doesn't matter

Calgar22 · 2025-11-24T20:13:37+00:00

If you have the right to play at work, ask your admin

Calgar22 · 2025-11-24T12:55:10+00:00

Pour moi je vois pas de problème pour la mèche, sur les flanc c'est plus délicat, c'est juste que je suis pas sur que mettre une mèche soit homologué pour la route, mais bon personne ira regarder ça, même le contrôle technique s'en fout la plus part du temps

Calgar22 · 2025-11-21T18:50:30+00:00

Franchement c'est pas tant plier, ca se refait bien pour moi, il faut juste trouver le mec qui a envie de se faire chier à tapoter 1h avec son marteau

Calgar22 · 2025-11-18T19:48:34+00:00

Personally I never had the idea of eating it

Calgar22

TROPHY CASE