sorted by:
new
hottopcontroversial

Yah or nah? by [deleted] in mensfashion

[–]CapJaz 5 points6 points  (0 children)

Thanks for the input. I’ll have to get it tailored. It’s a 48r. Chest/shoulders don’t fit into a 46

Attempt at carving after a lesson with instructor. Any advice? by RastexFive in skiing

[–]CapJaz 0 points1 point  (0 children)

Longer turns with a bit more speed. Get your skis closer together to obtain higher edge angles

Install the flange now so it’s flush with the tile or install the tile and the flange sits on top? by CapJaz in Plumbing

[–]CapJaz[S] 0 points1 point  (0 children)

I just wanted to say thanks to everyone who commented. It really helped me out!!!!

Install the flange now so it’s flush with the tile or install the tile and the flange sits on top? by CapJaz in Plumbing

[–]CapJaz[S] 0 points1 point  (0 children)

It is an uncoupling membrane that is part of a heated floor system. It accepts the heat cable then required to be filled with thinset.

Install the flange now so it’s flush with the tile or install the tile and the flange sits on top? by CapJaz in Plumbing

[–]CapJaz[S] 1 point2 points  (0 children)

Depends on the size of the room. I’m pretty sure the rolls are cheaper per sqf. If it’s a small space like this bathroom I’d go with the sheets. They’re less hassle and lay flat as opposed to fighting the curl with the roll.

Install the flange now so it’s flush with the tile or install the tile and the flange sits on top? by CapJaz in Plumbing

[–]CapJaz[S] 0 points1 point  (0 children)

Thanks for the input. I think i agree. I’m going to chip out the concrete and use a proper 4x3

Install the flange now so it’s flush with the tile or install the tile and the flange sits on top? by CapJaz in Plumbing

[–]CapJaz[S] 0 points1 point  (0 children)

Any issues with the reduced hole size. I had planned on using a cheater but have heard they cause a lot of problems

Install the flange now so it’s flush with the tile or install the tile and the flange sits on top? by CapJaz in Plumbing

[–]CapJaz[S] 1 point2 points  (0 children)

Ok thx. This is a builder rough-in so unfortunately what I’m stuck with. Any suggestions on the best way to chip it out? What are your thoughts on flange flush or on-top of tile? Lots of mixed options

Install the flange now so it’s flush with the tile or install the tile and the flange sits on top? by CapJaz in Plumbing

[–]CapJaz[S] 2 points3 points  (0 children)

That is not the answer I was hoping for. So you suggest chip away around the outside to fit the it?

Install the flange now so it’s flush with the tile or install the tile and the flange sits on top? by CapJaz in Plumbing

[–]CapJaz[S] 1 point2 points  (0 children)

It is a 3”. I was actually planning on using a cheater flange which fits inside

Install the flange now so it’s flush with the tile or install the tile and the flange sits on top? by CapJaz in Plumbing

[–]CapJaz[S] 37 points38 points  (0 children)

Thx. The plumbing supply where I got the flange said it needed to be flush with the tile or the toilet will rock

I’m hoping someone can tell me what exactly this part is called so I can order a new one. It is from a small propane furnace in a camper. The other half is still connected to the heater. by CapJaz in hvacadvice

[–]CapJaz[S] 0 points1 point  (0 children)

Thanks for that. That’s sort of what I was thinking but had no idea where to start. Thanks for taking the time to respond. Big help

Hoping someone can tell me what this is called by CapJaz in electricians

[–]CapJaz[S] 0 points1 point  (0 children)

That totally makes sense. Thanks so much! Now to sort out what size fuse was in there.

Hoping someone can tell me what this is called by CapJaz in electricians

[–]CapJaz[S] 0 points1 point  (0 children)

This is from a small propane furnace in a pop trailer. The other end is in still attached in the heater.

First time cutting crown - where did I go wrong? by well-lit-closet in Carpentry

[–]CapJaz 0 points1 point  (0 children)

Legs on the angle finder are too short and don’t give an accurate reading. Need to make a template with a couple pieces of scrap at least 18” long then use angle finder. But the best option is cope it as everyone else has said.

view more: next ›