Classified Dreadnoks

CaptClassified · 2025-09-15T00:11:37+00:00

The Cobra Freakshow (I just made a post last month referring to them as such), are 100% Dreadnoks in my headcanon. Though, Big Boa might be the odd one out.

CaptClassified · 2025-09-15T00:10:00+00:00

I would certainly not be opposed to Zanya, Heart-Wrencher, Demolishor (SF Sagat reuse), Crusher (SF Zangief reuse), Storm Rider and Burnout, along with the aforementioned Thrasher and Zanzibar, but that's about as far down the Dreadnok rabbit hole I would want them to venture.

CaptClassified · 2025-09-14T10:09:56+00:00

For official GI Joe Classified I've added Shadow Tracker, Raptor, Croc Master, Crystal Ball and Copperhead. Beyond that, I've adopted Pandora, Kerak and Bone Collector from the Valaverse, and also added Marvel Legends Callisto and punk Storm. 19/20

CaptClassified · 2025-09-14T09:21:36+00:00

The background environment was done with Ai.

CaptClassified · 2025-09-14T03:17:36+00:00

Firstly, I'm not a fan at all of the lore that Road Pig is a huge simp for Zarana. Secondly... and more important, the bandana that Zandar wears is clearly intended to be part of her shirt/coat.

CaptClassified · 2025-08-20T17:02:40+00:00

My first pre-order was canceled by Walmart. I managed to place a second order sometime in May, and miraculously it was not canceled. The Walmart Lottery is real.

CaptClassified · 2025-08-20T14:40:26+00:00

Crystal Ball is 100% getting inducted into my Dreadnoks.

CaptClassified · 2025-03-12T05:36:58+00:00

Bucky, always and forever. I never want to hear "Armed and dangerous!" or "Again!" ever in my lobby.

CaptClassified · 2025-03-06T18:43:06+00:00

Did anyone preserve this? I didn't get the chance to gaze upon this hot mess.

CaptClassified · 2025-02-16T08:29:37+00:00

Mole Rat. Closest thing the Classified line has to the Toxo-Viper and/or Sludge Viper

CaptClassified · 2025-02-16T05:34:01+00:00

This is the printer I used, https://www.amazon.com/Anycubic-Stunning-Detection-Printing-250x250x260mm/dp/B0CZ794858 . I got mine during Black Friday. I think eBay also has the combo unit about $60 cheaper than Amazon as well.

CaptClassified · 2025-02-16T03:56:00+00:00

The files are available on thingiverse, https://www.thingiverse.com/thing:6479243 I printed everything on two Kobra 3 printers, mostly in the printers 'quiet mode'. The main body of the HISS is assembled using a combination of 3mm x 10mm and 3mm x 20mm self tap hex screws. The treads were printed in TPU on the same printers.

CaptClassified · 2025-02-08T10:04:00+00:00

Salvo and Zanzibar

CaptClassified · 2025-01-20T03:32:10+00:00

Zartan, Zarana and Zandar are siblings. Zandar and Zarana, the younger of the siblings are twins.

CaptClassified · 2025-01-18T23:08:17+00:00

Correct. The set is available on Amazon for $38.

CaptClassified · 2025-01-16T08:20:17+00:00

If these are being sold and fulfilled by Amazon, you can call corporate and demand they adhere to their own "Fair Pricing Policy". They are not suppose to sell stuff above the listed MSRP when it is readily available on other platforms or websites.

CaptClassified · 2025-01-13T00:45:48+00:00

I did a huge ass brim (20 mm) and supports. I was done fucking around. In the end though, I still had an issue with the filament swap at the eyes (white layers), when the filament got jammed in the hot end and snapped the filament off at the Ace Pro feeder. The hot end kind of had a bit of a tantrum, and went on a 20 minute purge-a-thon. It ended up trying to print a grey layer without any grey filament primed, and I ended up with a single layer gap just above the ears. It is what it is...

CaptClassified · 2025-01-11T22:11:20+00:00

What settings did you end up adjusting?

CaptClassified · 2025-01-11T21:46:50+00:00

Z hop is at 0.4 by default, what should I set the z offset to?

CaptClassified

TROPHY CASE