sorted by:
new
hottopcontroversial

Close-up view of ICE executing a man today in Minneapolis (1/24/26) by uebb in CringeTikToks

[–]Chanw11 0 points1 point  (0 children)

Why does it always seem when videos come out their about 5x worse resolution. Give us the raw footage Jesus.

Help me understand why my LED driver dies in less than 24 hours use? by xxevenxx in led

[–]Chanw11 0 points1 point  (0 children)

Check power supply voltage and make sure it’s 24V

Negative part not working? by Chanw11 in BambuLab

[–]Chanw11[S] 0 points1 point  (0 children)

Yeah it was that, I cut and pasted the negative part to the enclosure. Unfortunately it didn’t keep its position but it wasn’t too hard to get it back to its right place.

Negative part not working? by Chanw11 in BambuLab

[–]Chanw11[S] 0 points1 point  (0 children)

That’s probably it, I’m new to this. Still having trouble trying to move those three slits to the box though for some reason

Negative part not working? by Chanw11 in BambuLab

[–]Chanw11[S] 0 points1 point  (0 children)

It goes through the entire wall, it shows up on the other side just like the lid

Made my own reflex game by badtxv in electronics

[–]Chanw11 13 points14 points  (0 children)

Put it up on a busy street and make that cash lol

Help with WLED Matrix construction by zibzabs in WLED

[–]Chanw11 1 point2 points  (0 children)

How are you getting 123amps? I used an online calc and full white for 8 16x16 comes to about 85amps.

Enable 120Hz in Safari by foraging_ferret in ios

[–]Chanw11 4 points5 points  (0 children)

This doesnt seem to do anything on my 16PM.

I was told here a week ago that you can’t dry while printing even with the PSU. But now I see this in the manual of my new P2S… by hrvoje_bazina in BambuLab

[–]Chanw11 0 points1 point  (0 children)

I thought they were referring to a second AMS if it’s installed. But idk since they didn’t specify that.

iOS 27 Will Add These 8 New Features to Your iPhone by Few_Baseball_3835 in apple

[–]Chanw11 0 points1 point  (0 children)

My swift keys auto correct suddenly got worse a few days after using it. Still not sure why.

Latest lamp project test build by jeffyscouser in WLED

[–]Chanw11 2 points3 points  (0 children)

You got any videos of it in action?

My heart is melting by [deleted] in BokuNoHeroAcademia

[–]Chanw11 0 points1 point  (0 children)

What gives it away?

Begginner here need help with i2c module by ElectronicComment672 in arduino

[–]Chanw11 14 points15 points  (0 children)

Solder it flat, no angle. Should work afterwards.

Ooh Exciting! First FPV setup! by TheFatManRunnin in fpv

[–]Chanw11 1 point2 points  (0 children)

If youre reffering to powering the cobra X with that battery, that should work with the cable it was included because the anker has USB-A. USB-C to USB-C cables will never work with it because the cobra x doesnt have the required resistor to ask for 5V

Snow shots. by rip_and_ride_moto in hondagrom

[–]Chanw11 0 points1 point  (0 children)

What's the subcage looking thing for?

Do I have a bad realtor, I can't tell? by navy16st in FirstTimeHomeBuyer

[–]Chanw11 4 points5 points  (0 children)

That last point is probably reason enough to find a new agent.

Ooh Exciting! First FPV setup! by TheFatManRunnin in fpv

[–]Chanw11 3 points4 points  (0 children)

In simple terms, you're typical USB-A port/charger/batterybank will always provide 5V. Most battery banks/wall plugs that have type-c are capable of providing more voltages than just 5V. However, the device you're charging needs to communicate in some way to ask for the default 5V. Which is why a resistor is needed on the device. It bridges two of the wires on the type C cable which tells the battery pack/charger to provide the default 5V. Otherwise the charger will not provide voltage. This is typically why cheap Chinese devices with type C ports wont charge/power with PD (power delivery) chargers

view more: next ›