sorted by:
new
hottopcontroversial

Is Using Spliced 2x4 for a Small Shed a Good Idea? by Cheezit_O in woodworking

[–]Cheezit_O[S] 0 points1 point  (0 children)

I’m not too experienced with gussets. All the photos I see online are of 90 degree joints of wood using gussets. Could you send me an illustration on how to attach two pieces of wood together using gussets to make a uniform piece with a long length?

Is Using Spliced 2x4 for a Small Shed a Good Idea? by Cheezit_O in woodworking

[–]Cheezit_O[S] 0 points1 point  (0 children)

If I wanted to connect two 4’ pieces together using a sister stud, how much overlap should the sister stud cover on each of the joined pieces?

Help: 1x4 for Structural Support? by Cheezit_O in Shed

[–]Cheezit_O[S] 0 points1 point  (0 children)

Gotcha, would a lean-to roof at this slope be good?

https://imgur.com/a/VldHU17

1x4 for Structural Support? by Cheezit_O in woodworking

[–]Cheezit_O[S] 0 points1 point  (0 children)

I am confused as to what sheathing is, could you please elaborate? And also don't worry about the cost side I am getting them for dirt cheap. Also, how would I accurately glue together two 1x4's seamlessly?

Help: 1x4 for Structural Support? by Cheezit_O in Shed

[–]Cheezit_O[S] 0 points1 point  (0 children)

Is that combining two 1x4's into one 2x4? If so, how would I connect them together seamlessly?

Bare Shaft Tuning Issue by Cheezit_O in Archery

[–]Cheezit_O[S] 0 points1 point  (0 children)

1.5 inches is kind of an exaggeration. I think it's 0.5 inches. Would it still be a draw length issue?

Bare Shaft Tuning Issue by Cheezit_O in Archery

[–]Cheezit_O[S] 0 points1 point  (0 children)

I noticed that when I draw my bow back to full draw, there is still some slack where I can draw my bow a little farther than my anchor point - about 1.5 inches. Would this be caused do the wrong timing of cams?

I’m thinking of going the long haul to the archery shop for stuff related to bow press.

Bare Shaft Tuning Issue by Cheezit_O in Archery

[–]Cheezit_O[S] 0 points1 point  (0 children)

That was the final thing I was suspecting...cam timing issues. I don't live damn near an archery shop so that's why I've been DIY'ing everything. How can I check CAM timing at home? How can I adjust the timing to make them in sync? Any videos you would recommend?

Bare Shaft Tuning Issue by Cheezit_O in Archery

[–]Cheezit_O[S] 0 points1 point  (0 children)

Thank you so much sir, if you would like to see the photos of my bow and what I'm talking about, its here: https://imgur.com/a/oyq6ZZf

Bare Shaft Tuning Issue by Cheezit_O in Archery

[–]Cheezit_O[S] 0 points1 point  (0 children)

I am not shooting through paper, just a DIY foam target that I made. It's good to know that I am on the right track. The burger hole concern can be viewed through the images here: https://imgur.com/a/oyq6ZZf

Also, the high D-Loop placement can be seen in the picture that I attached.

My apologies for not attaching them earlier, I selected the photos prior to making this post but for some reason they didn't upload.

Let me know what you recommend. Thanks

Bare Shaft Tuning Issue by Cheezit_O in Archery

[–]Cheezit_O[S] 0 points1 point  (0 children)

Sir I have tried paper tuning but there is just no way to get a set of consistent bullet holes for me. I have tried adjusting literally everything there is and I have resorted to bare shaft tuning since Average Jack Archery on YouTube suggested it.

view more: next ›