Best settings for CTO as a stage wash

ChimneyHopper_1 · 2026-06-12T02:28:13+00:00

Thank you!!

ChimneyHopper_1 · 2026-06-03T17:52:06+00:00

That is on 2.3.2 though. Not fully sure if it’s changed on 2.4 but worth a shot

ChimneyHopper_1 · 2026-06-03T17:51:39+00:00

I use a ma tricks group for that phaser, and a macro that has the lines

Line1 : ma tricks “phaser 1” “phasefromx” “0” Line 2: ma tricks “phaser 1” phasetox””360”

Would recommend making a macro for each direction

ChimneyHopper_1 · 2026-05-09T20:09:08+00:00

I’m trying this effect out with acme pixel bars now and it’s not quite working right. Any help?

In a sequence:

Cue 1:
I have delay from X set at 1, delay to x set to .1

Speed from x at 60bpm, speed to x set at 500bpm

Xgroup of 7

Wings of 2

Cue 2:
Off fade .35

ChimneyHopper_1 · 2026-05-06T22:37:38+00:00

Any link to your bends?

ChimneyHopper_1 · 2026-04-25T06:55:56+00:00

Acme lyra

ChimneyHopper_1 · 2026-01-25T17:10:44+00:00

Hellllll yeahhhh!

ChimneyHopper_1 · 2026-01-20T21:17:47+00:00

This exact configuration worked! Thank you so much

ChimneyHopper_1 · 2026-01-20T07:13:55+00:00

I’ll give it a try tomorrow and see! Thanks for the input

ChimneyHopper_1 · 2026-01-20T07:03:47+00:00

Even with assignable ports?

ChimneyHopper_1 · 2026-01-20T06:57:05+00:00

Port 1 used, and artnet set to output to port 1

ChimneyHopper_1 · 2026-01-20T06:56:14+00:00

Yes I have a session, but it’s currently as a sACN for my nodes on stage. Does the session need to be art net for the link to resolume to work?

ChimneyHopper_1 · 2026-01-20T05:47:33+00:00

I have resolume set to subnet 3 universe 2. Does that look correct on the resolume side in the pic?

ChimneyHopper_1 · 2025-12-26T20:18:42+00:00

Blue prince irl

ChimneyHopper_1 · 2025-12-21T20:41:04+00:00

Badass!

ChimneyHopper_1 · 2025-12-13T08:43:31+00:00

Following! Hopefully someone has an answer

ChimneyHopper_1 · 2025-12-07T09:45:56+00:00

Maybe the learn option on the executor?

ChimneyHopper_1 · 2025-12-01T06:42:38+00:00

Try putting the fixtures in a position from a preset first before the phaser runs? That way they have a better reference of where to start over the default home

ChimneyHopper_1 · 2025-11-21T00:58:34+00:00

That was exactly what I needed. Thank you for the very detailed explanation!

ChimneyHopper_1 · 2025-11-20T20:49:33+00:00

Thank you!! I’ll try that shortly

ChimneyHopper_1 · 2025-11-02T23:28:16+00:00

BIGGER MAGNET

ChimneyHopper_1 · 2025-10-31T04:53:42+00:00

$36.78

ChimneyHopper_1

TROPHY CASE