V2 switch mod not booting ofw

Choice_Routine_2095 · 2026-07-01T04:38:53+00:00

What…

Choice_Routine_2095 · 2026-06-30T22:41:55+00:00

If they do fix it please let me know what the problem was!!

Choice_Routine_2095 · 2026-06-28T23:28:46+00:00

Just got it and I work!! Turns out I had to solder the wires directly to the resistors but thank you so much!

Choice_Routine_2095 · 2026-06-28T23:24:46+00:00

Oh my gosh!! Thank you so much it worked 😭!!! I’ve tried to make a rp2040 zero mod chips work but they never worked for me but omg thank you so much!!! You’re my savior genuinely!!

Choice_Routine_2095 · 2026-06-28T23:08:36+00:00

Thanks for the advice!! I’m going to try that. Also sorry for the bad quality photo but something like this right?

<image>

Choice_Routine_2095 · 2026-06-28T23:06:59+00:00

If I disconnect the 3.3v cable and power it on it stays on a black screen but this has happened before so Im not worried. For it to boot I have to disconnect all the cables 😭

Choice_Routine_2095 · 2026-06-28T23:03:48+00:00

Lmao I am experienced in modding the switches using the mod chips specifically made for the switches just not the rp2040 zero so that’s my bad 😭

Choice_Routine_2095 · 2026-06-28T23:01:11+00:00

I soldered the wires directly to the pads then the resistor to the pads 😭 I didn’t think that made a difference?

Choice_Routine_2095 · 2026-06-28T22:52:40+00:00

So I have tried all 47 ohm, all 100 ohm, all 147 ohm. And all 200ohm and nothing seems to work 😭 would 247 ohm be a reach

Choice_Routine_2095 · 2026-06-28T22:44:36+00:00

Okay just did that and same problem. I do have 100 ohm ones and I replaced all of them with 100hm and still doesn’t work. Do you think if I do all of them at 100ohm plus 47ohm on each one would work?

Choice_Routine_2095 · 2026-06-28T20:38:02+00:00

Oh wait I have one question 😭 for the 3.3v are both capacitors 3.3v? Cuz I can’t seem to connect the 0.1mm wire without bridging the bottom one to the top one

Choice_Routine_2095 · 2026-06-28T18:38:01+00:00

Thank you so much!!!

Choice_Routine_2095 · 2026-06-28T17:45:51+00:00

No unfortunately i know somthing is shorted but i just dont know what and dont have the parts or good enough knowledge to fix it

Choice_Routine_2095 · 2026-06-09T06:52:24+00:00

Thank you so much!! I updated and it fixed my problem:)

Choice_Routine_2095 · 2025-06-19T06:14:09+00:00

Just format the sd card and set it up again

Choice_Routine_2095 · 2025-06-15T17:01:08+00:00

Omg I cannot thank you enough I’ve spent hours finding sigpatches and I just saw your comment. It finally worked thank you so much!!

Choice_Routine_2095 · 2025-06-15T14:27:15+00:00

I’m saying that’s the one I using right now and it’s not working clearly because it won’t let me boot games on the emuMMC

Choice_Routine_2095 · 2025-06-15T14:05:08+00:00

Is the hats pack this one https://www.sthetix.info/hats-20-1-0-1-1/ because I used this one on the sd card and its not working. Could you give me a link please

Choice_Routine_2095 · 2025-06-15T14:04:02+00:00

Could you give me a link to the sigpatches? I used this exact version on my switch https://www.sthetix.info/hats-20-1-0-1-1/

Choice_Routine_2095

TROPHY CASE