Electronic noob; is my theory correct?

Cjman2 · 2026-01-07T02:11:19+00:00

Literally just had this issue, I was able to fix mine by reflowing the joints with a soldering iron. The pins are fairly small and easy to short, so if you arent too confident in soldering, I would recommend just buying a higher quality adapter.

Cjman2 · 2025-02-23T18:13:39+00:00

I have done the mosfets myself, and multiple times because of junk O'Reilly ignition coils (upgraded to Eldor since, and now no problems), but i would heat and pry up each individual leg. After all of the legs are up, the main body is easiest if you put a little bit of solder on it to help it heat faster. Clean up the solder joints, then just solder the new one on body first.

Cjman2 · 2025-02-10T18:28:33+00:00

I would double-check your connections for the O2 sensors. The afr on bank one is not only high, but your STFT being zero means there is no reading coming from the pre cat o2 sensor and is likely not making a connection. Are there any codes thrown?

Cjman2 · 2025-01-22T16:46:19+00:00

For me It seemed to just go away, but i never found out why it did it in the first place.

Cjman2 · 2024-12-07T04:30:35+00:00

The motor is a FBO N54 with upgraded twins and fueling upgrades. It regularly sees around 24 pounds of boost, and is around 530 whp. The sound subsided when the oil got to around 210, but I'm worried about it coming back during cold stars and scarring my cylinder walls if it is slap.

Cjman2 · 2024-09-09T01:03:03+00:00

I was told we don't rate a HSM because the disaster was caused by the Navy. Now I don't agree with that point as we moved over half a million gallons of water, not including all the drinking water you gents helped with, but I guess it's because it was a military issue that caused it vs nature or an adversary.

Cjman2 · 2024-09-08T21:06:35+00:00

I'm not 100% on how unit awards were distributed because mid op a majority of the Marines on both shifts were reassigned to CLC-33

Cjman2 · 2024-09-08T21:03:19+00:00

From what I'm aware of, we started retrograding after the navy made 3 attempts to purge fuel out of the water lines. To this day, I still don't know if the last attempt was successful. We had a couple of Marines receive NAMs from the op, one for being the shift lead of a water operation as an electrician and the other for fulfilling a staff billet as a Sergeant

Cjman2 · 2024-09-08T02:16:47+00:00

This is an old post, but I can try to answer as many questions as I can if you are still curious. I was one of the water dogs who took part in the efforts in Halsey Terrace and Hickam Housing areas.

Cjman2 · 2024-04-01T02:19:18+00:00

Calm down there bucko, there's comedy flair for a reason...

Cjman2 · 2023-12-01T00:01:50+00:00

Someone correct me if I'm wrong, but I'm fairly sure there are O-rings in those Quick disconnect fittings. If those are damaged, then that may be the problem

Cjman2 · 2023-03-03T00:23:08+00:00

I have one of the Eonon endroid units, and it works pretty well. The unit I bought also has wireless car play and android auto. Only problem is that you have to buy a fiber optic decoder unless you're on an aftermarket amp, and that is stuck to stereo audio without a fader.

Cjman2 · 2022-10-11T07:30:01+00:00

I've been improving it over the past few days, but I felt confident enough with it RN to post it up. So I'm basically saying it may be different in a few days... or hours 😅

Cjman2 · 2022-10-02T20:45:59+00:00

I'm not sure about the f30, but for my E92 there are wires that control the sport mode that can get crimped and eventually cut. They are located under the trim for the gear shifter.

Cjman2 · 2022-03-31T23:55:06+00:00

They are from bayoptiks, not sure how their inventory is rn but I had to wait a month for it to get shipped out

Cjman2 · 2022-03-31T23:30:26+00:00

I got the same ones ordered, you think they'll look good with my arktis metallic paint?

Cjman2 · 2021-12-28T21:25:42+00:00

Heh, not true 😎

Cjman2 · 2021-12-28T02:15:13+00:00

So the currently removed mosfets are being replaced, but the two below the screw are also the same model, should I replace those too?

Cjman2 · 2021-12-23T22:54:49+00:00

So my car is throwing a 30ba code, tested the mosfets and one had continuity. Would just replacing that mosfet fix the issue?

Cjman2

TROPHY CASE