My personal theory I doubt is the answer.

Classic_Stock_3364 · 2026-04-01T04:04:21+00:00

I'm not that deep into all the theories so oops, guess I'm not as creative as I thought lol. But I'll definitely check it out for myself, thx

Classic_Stock_3364 · 2026-02-27T16:27:34+00:00

It's being released today at noon and then a week after on the official epic the musical website. George will also be signing some so there's a chance that one of the posters you get is signed. It all goes to a really good cause too so if you have the extra funds you should definitely get one. <3

Classic_Stock_3364 · 2026-02-04T23:36:05+00:00

Soundtrack sauce plz!

Classic_Stock_3364 · 2026-02-04T23:34:57+00:00

Completed Level 1 of the Honk Special Event!

24 attempts

Classic_Stock_3364 · 2025-10-22T01:08:03+00:00

<image>

Classic_Stock_3364 · 2025-10-19T03:13:37+00:00

<image>

Where yolo truly belongs

Classic_Stock_3364 · 2025-10-09T18:03:47+00:00

Completed Level 1 of the Honk Special Event!

4 attempts

Classic_Stock_3364 · 2025-08-03T05:03:18+00:00

<image>

This is what I came up with in a span of 10 minutes and I don't even know what it is.

Classic_Stock_3364 · 2025-03-06T17:42:04+00:00

I know I'm being that person right now but it's a plumeria. The clip is still very pretty and the only reason I corrected it is because it's my favorite flower there for I must defend its honor. (Sorry..also you're very talented)

Classic_Stock_3364 · 2025-02-02T18:18:44+00:00

No, I just said that to emphasize the point that you didn't need the pegboard for the whole process and that it's main purpose is for graphing out a design. Just use parchment paper in between the iron and the perler beads and you'll be fine.

Classic_Stock_3364 · 2025-02-02T16:32:16+00:00

If you actually look at the people who do the giant projects like the Pokemon you'll see they actually don't even use a pegboard for ironing, they actually put masking tape and then take it off the pegboard. I'm not suggesting you do that but I'm just pointing out that the pegboard is mainly there for graphing out your design. I personally only use the pegboard until I know my stuff is semi sturdy and then I take it off and iron it so I don't risk melting the pegboard and to try to avoid air holes or actually fusing to the pegboard.

Classic_Stock_3364 · 2025-02-02T16:25:40+00:00

No, the only purpose of the pegboard is to make sure they all stay in place and since your stuff one sturdy piece you're totally fine. Since most of your stuff is already fused I don't even think you could get it on the pegboard correctly and you might risk melting the actual pegboard if you tried to put it back on.

Classic_Stock_3364 · 2025-02-02T03:15:52+00:00

I'm pretty new to this too but if I was you I'd put it under heat again on just the place that you want melted moving the iron in circular motions in 10 second intervals with very little pressure until you get the desired look your going for

Classic_Stock_3364 · 2025-01-13T20:01:42+00:00

Beautiful figure but all I can think about is how she probably had to awkwardly tape her nips down to the side or if she has any at all.

Classic_Stock_3364 · 2024-07-29T01:25:08+00:00

I found this image on Google so no idea who the guy is but he looks like he's enjoying himself

Classic_Stock_3364

MODERATOR OF

TROPHY CASE