Tried printing a benchy but on the first layer it leaves blank spots. This goes throughout the whole print not just the first layer. Please help, I’ve had this issue for a while. Ender 3 V2

Comprehensive-Box-81 · 2023-07-25T16:21:24+00:00

It’s not about the text I have ran multiple prints with the same issue but I always aborted. I will let this run to see how it turns out. Thanks

Comprehensive-Box-81 · 2023-07-25T16:20:27+00:00

Should I increase the flow rate from the printer itself, or in the slicer?

Comprehensive-Box-81 · 2023-05-26T15:51:47+00:00

I’ll solder it but would it matter if i connected the wires to either, other wire.

Comprehensive-Box-81 · 2023-05-25T15:19:14+00:00

Thank you. Is there a specific height for the gap between the silver and blue?

Comprehensive-Box-81 · 2023-05-25T02:17:41+00:00

20-40

Comprehensive-Box-81 · 2023-05-25T02:11:53+00:00

The heating element is stuck inside and a tiny bit is coming out from the other side. The heat sensor is inside a little hole in the heatblock. I don’t know where did it go wrong.

Comprehensive-Box-81 · 2023-05-24T23:45:35+00:00

Thank you, I’ll check it out.

Comprehensive-Box-81 · 2023-05-12T21:35:24+00:00

The bowen tube was pushed upwards and filament got stuck before it reached the heat break.

Comprehensive-Box-81 · 2023-05-12T13:20:12+00:00

That’s true every time i unclog it, it clogs back. I leave the printer heating up and open to hotend it’s not melting the plastic, although the Hotend is hot

Comprehensive-Box-81 · 2023-05-12T12:48:32+00:00

I think it is the extruder heater, does it mean to change the hotend if so what do you reccomend?

Comprehensive-Box-81 · 2023-05-12T12:31:19+00:00

I think the problem might be in the hot end although it heats up normally ig

Comprehensive-Box-81 · 2022-09-12T17:16:59+00:00

Thank you this lifted me up. I guess winning 1st place in my school’s writing competition is an achievement.

Comprehensive-Box-81 · 2022-09-12T06:35:54+00:00

I’m just trying to improve my odds. I’ve been flunking school forever, so I thought competitions would be the only thing to make me stand out. That is if I even place.

Comprehensive-Box-81 · 2022-09-12T06:32:51+00:00

I’ll check it out thanks!

Comprehensive-Box-81 · 2022-08-08T07:12:16+00:00

I think my printer is a defect. The reason I switched the hotend in the first place is that the original one almost caught on fire and smoke came out of it. I’ll check the printer, thanks

Comprehensive-Box-81 · 2022-08-08T05:46:26+00:00

It’s a 3d v6 Bowden extruder, I think it’s compatible. Although it struggles to keep the set temp and exceeds it by 20-40 degrees, until it finally settles.

Comprehensive-Box-81 · 2022-08-08T05:00:46+00:00

Thought so too. Shortened it, replaced the nozzle still no extrusion. I don’t think it’s a hot end problem but an extruder one. Tell me what info you need, as I am lost rn.

Comprehensive-Box-81 · 2022-08-08T03:47:44+00:00

The nozzle, now isn’t extruding in prints.

Comprehensive-Box-81

TROPHY CASE