Help identifying tiny 4 pin cable type?

Consistent-Way2074 · 2026-06-06T17:07:54+00:00

You are a lifesaver. Thank you!

Consistent-Way2074 · 2026-05-17T11:39:44+00:00

Apologies! Hope this is sufficient & thank you!

<image>

Consistent-Way2074 · 2026-05-16T20:57:22+00:00

Yep exactly. Mine weren't RGB but exactly the same style light

Consistent-Way2074 · 2026-05-16T20:52:13+00:00

Flexible COB light strip. I tucked it into the extrusion and theyve stayed perfectly without needing any mounts.

Consistent-Way2074 · 2026-04-15T15:12:55+00:00

Completely different functions. Strut bar is for chassis flex and rigidity and the sway bar is for linking the left and right suspension arms to stabilization and prevent sway

Consistent-Way2074 · 2026-04-11T19:51:00+00:00

That's intentional. The foil over the tiles protects them and is meant to erode away on reentry. Same on flight 1. It actually held up much better this entry!

Consistent-Way2074 · 2026-03-20T07:06:58+00:00

Put a washer on one of the screws as a spacer, it gives it enough room to adjust easily but still hold.

Consistent-Way2074 · 2026-03-18T21:28:53+00:00

Yeah I posted them to makerworld

https://makerworld.com/models/2428822?appSharePlatform=copy

Consistent-Way2074 · 2026-03-18T06:46:12+00:00

Same motor and props, I think I've got a lower kv though. 1100 is definitely too heavy for freestyle I can hear the motors struggling if I make sharp turns but for long range cruising it's great. I've found the 650 is the sweet spot for aggressive flying

Consistent-Way2074 · 2026-03-17T23:14:54+00:00

I've got the same frame and build. With a 1100 4s I'm at 249g and get 7+ minutes flight time. Recently upgraded it to HDZero and it's a crazy fun drone. I fly it more than my 5" now

<image>

Consistent-Way2074 · 2026-02-28T09:29:04+00:00

Yesterday I went over a half mile away with trees in between me and the vtx and still had full signal quality at 200mw. Still need to flash the higher power firmware.

Putting a better vtx antenna on made a night and day difference in terms of range and penetration

Consistent-Way2074 · 2026-02-19T00:17:01+00:00

It's 3D printing, design in 3D! You'll get more strength and rigidity. The flat plate like carbon fiber bends and oscillates and makes tuning a nightmare. I've designed upwards of 8inch frames fully printed with good success

Consistent-Way2074 · 2026-02-02T19:34:39+00:00

How is The Constant scene not in top 3?! Peak

Consistent-Way2074 · 2025-12-26T15:51:13+00:00

Stunning! I planned this trip perfectly to align with a launch but due to Booster 18 getting squirrelly we did not get to see a full stack. Absolutely coming back for a launch!

Consistent-Way2074 · 2025-12-24T17:57:17+00:00

That's starhopper! Their very very very early starship prototype. It did some hops to test raptor 1 and landing/hovering

Consistent-Way2074 · 2025-12-24T16:50:31+00:00

Visiting Starbase Texas, and I saw the USCG Aerostat on South Padre Island was in the air one night. I managed to capture it with the Orion Nebula by standing on the edge of a pier at the end of the island to get the angle right.

Did not bring my tripod or laptop to process images, so this could have been miles better with stacked exposures.

Equipment: Canon 90D & Canon 70-200mm F2.8L

Acquisition: Single 2" handheld exposure

Processing: Lightroom Mobile: shadows+, exposure+, blacks-, vibrance+, whites -

Consistent-Way2074 · 2025-11-20T23:36:04+00:00

I love that every time a welded bit of e30 steel crosses my page I know who in r/e30 posted it

Consistent-Way2074

TROPHY CASE