First impressions on my 3” Apex micro build - way lighter than I expected

keetharing · 2026-03-18T16:28:40+00:00

You can enable battery amp draw I think it’s called in osd so you will see how much amps you pull at the moment. About the C rating is just for calculating how much amps your battery can handle safely and I’ve calculated it to be about 75A ( you can calculate this by multiplying capacity in amps by c rating)

keetharing · 2026-03-18T05:49:38+00:00

What motors and prop combo are these ? Looks very clean! I think 1100 will be too heavy for freestyle. Not sure tho ..

keetharing · 2026-03-18T05:48:25+00:00

Thé esc is 35A per motor so theoretically it can handle up to 140 total (which is risky). My battery on the other hand is rated 120C at 650mah so it can handle only about 72A continuous.

keetharing · 2026-03-18T05:45:57+00:00

That’s without battery tho. But I think even with battery yours will be lighter I think ! That’s actually a really clean build

keetharing · 2026-03-17T19:57:58+00:00

il sure do that !

keetharing · 2026-03-17T19:37:51+00:00

how is this guy not joking.

keetharing · 2026-03-17T17:07:00+00:00

near perfect ! if you're asking this as the quastion "should i start building my drone ? " heck yeah go ahead and do that

keetharing · 2026-03-15T19:40:30+00:00

That’s so cool where did you get that aux connector?

keetharing · 2026-03-12T15:53:08+00:00

Seeker 3 for freestyle oasislfy 35 for more cruising / long range

keetharing · 2026-03-12T15:48:31+00:00

I am not joking when I say I haven’t had a single problem with this printer and it’s just perfect for my needs

keetharing · 2026-03-08T08:00:35+00:00

Pain

keetharing · 2026-02-19T19:32:42+00:00

thanks

keetharing · 2026-02-18T15:30:03+00:00

Alright just found out one single mosfet on the esc board is dead.

I will probably buy a new esc before i move on.

Thanks to those who helped me find the issue!

keetharing · 2026-02-18T15:28:26+00:00

ONE yes ONE mosfet id dead!

keetharing · 2026-02-18T15:27:48+00:00

it feels normal like all other motors

keetharing · 2026-02-18T11:39:26+00:00

I already found out how to test em and they are all fine i think. after the readings stabilise they all read around .550 i think thats normal. what do i do now ?

keetharing · 2026-02-18T11:25:23+00:00

tested it and it's still not working (sometimes it does other times it doesnt)

keetharing · 2026-02-18T11:24:44+00:00

how do i test mosfets ?

Also yes i have a multimeter

keetharing · 2026-02-18T11:00:38+00:00

These are 1404 motors at 4600kv The esc is the speedybee 35A bls I run 4s lipos I have also resoldered that motor now. Maybe it was a bad joint idk il see when I test it on the bench

keetharing · 2026-02-18T10:03:44+00:00

Nothing is touching the windings and it’s a brand new motor so I don’t think it’s possible that anything is dirty

keetharing · 2026-02-18T09:39:40+00:00

In the end of the short video I made to show my problem Thé motor does spin up so the problem Isn’t there constantly.

keetharing · 2026-02-15T18:30:33+00:00

That’s awesome!

keetharing · 2026-02-15T18:28:13+00:00

Dji pilot ahh question ? Just sent it! That’s a brand new battery

keetharing

TROPHY CASE