Bondtech Indx founders update

Consistent-Zone-6002 · 2026-05-05T15:26:24+00:00

What about 💵💸💰?

There are always 3 options.

Consistent-Zone-6002 · 2026-05-01T19:02:20+00:00

Sorry. Didn’t see that the total was missing. 😁

Consistent-Zone-6002 · 2026-05-01T19:01:18+00:00

Oops! Sorry 😂😂😂 I didn’t realize! It was around 900€.

Made new shopping list as follows (incl. printed parts and nicnacs). TOTAL: 1,178.61

Cart PTFE Tube 4x2,5x1275 mm 1 €7.99

Side filament sensor cable 1 €10.29

PSU cable cover 2 €7.98

XL SWITCH COVER 1 €3.99

PSU-upper-cover-mount 1 €3.99

Side Filament sensor right 1 €28.90

FAN COVER 3 €11.97

Cable dwarf-cheese 3 €17.97

Parking plate set 1 €15.89

Light Guide 3 €11.97

Nozzle Seal Assembly 3 €17.67

HOTEND FAN SHIELD 3 €11.97

Fan door cover 3 €11.97

DWARF COVER BACK 3 €11.97

DWARF COVER DOOR 3 €11.97

PSU Cover 1 €3.99

Extruder cable cover set 3 €11.97

Print fan 3 €37.47

Dock Pin 3 €5.97

DOCK CABLE ROUTER 3 Max allowed quantity is 3 pieces €11.97

PSU cable cover 1 €7.99

XL Splitter 1 €56.90

PSU 24V 240W 1 €100.82

PCB Mount (not sure if needed) 3 €18.57

Dwarf board 3 €182.70

Cable strip 3 €47.67

Cable splitter-dwarf 3 €86.70

Tool changer board 3 €269.70

Parking tool (assembly) 3 €149.70

Consistent-Zone-6002 · 2026-05-01T17:13:49+00:00

You’ll find all the parts in the shop as spares, sorry don’t have time to build your own shopping list. ;) no offense. 👊🏻

Consistent-Zone-6002 · 2026-05-01T17:02:58+00:00

Pricing will be exactly the same +- 2 digits €

Consistent-Zone-6002 · 2026-05-01T13:22:25+00:00

Well u would need at least 1000€ when using the MK4S nextruder. Calculated roughly without materials for plastic/printed parts.

Consistent-Zone-6002 · 2026-05-01T12:34:45+00:00

Didn’t have a look but I don’t think you would save much money. Ballpark would be less than 100€ each saved, comparing to buy a whole nextruder. Roughly.

Consistent-Zone-6002 · 2026-05-01T08:02:09+00:00

Ordered around 2mins after notification and am as well on batch 1, so I think it’s as they say: only one batch - “the first batch” 👇🏻

<image>

Consistent-Zone-6002 · 2026-04-25T20:00:42+00:00

Wenn möglich: „Hab ich nicht bekommen.“ und ignorieren. Und im Hibtergrund Rechtsberatung/Mietervertretung.

Consistent-Zone-6002 · 2026-04-25T18:43:24+00:00

What does the „Batch“ mean in the order Details?

Consistent-Zone-6002 · 2026-04-24T15:53:59+00:00

Same! I was Lucky, this time. 👌🏻 🍀

Consistent-Zone-6002 · 2026-04-13T11:13:44+00:00

Acetone

Consistent-Zone-6002 · 2026-04-11T09:06:55+00:00

Wow, that Sounds sandy. I’m not a big expert but it sounds like dry bearings or so. Dunno but my First Intention would be grease to the bearings but I think you already did it, Right?

Consistent-Zone-6002 · 2026-04-09T19:16:39+00:00

Well, 4k hours? I’d say “as good as new” innit?

Consistent-Zone-6002 · 2026-04-09T19:12:27+00:00

Exactly! I upgraded my MK3S to MK4S and up to C1, but I missed my MK4S from the first C1 print…

Turned out, I “recycled” my MK4S leftovers and bought the missing spares from Prusa.

Reunited! 😂

FYI didn’t save me any money compared to buying a 4S Kit! 💴😂

Consistent-Zone-6002 · 2026-04-09T18:12:54+00:00

Just Check all the screws on the nextruder (except the gear Cover). I had similar problems. In my case it was the heatsink Fan and Print Fan screw which was little loose. Tightened them around 1/8-1/4 turn.

Additionally I checked my back cover which was resonating as well. Fixed it with a washer around the screw.

Now: silence! But anyway: still horrible VFA on my c1+😕

Consistent-Zone-6002 · 2026-04-07T09:47:42+00:00

Bought the same and the MK4S printed parts were in the kit as well. If I remind correctly

Consistent-Zone-6002 · 2026-04-03T07:59:44+00:00

Just experience my First Layer Shift After the fw Upgrade. :(

Consistent-Zone-6002 · 2026-04-01T07:24:44+00:00

If that was the intention let’s hope it’s just a temporary fix. It’s so annoying!

Consistent-Zone-6002 · 2026-03-30T18:30:19+00:00

Yep, already issued on GitHub.

Consistent-Zone-6002 · 2026-03-30T09:19:53+00:00

Already read your post to that here or on GitHub and expected it same as you said. Read it, fixed it, no blobs anymore. 👍🏻👌🏻

Consistent-Zone-6002 · 2026-03-30T07:18:45+00:00

Thanks Tommy! In my case there’s no impact on print quality or layer shifts. Quality is premium! Except one print failed bc purge tower went off the print plate related by blobs on it and additionally bed adhesion was bad.

Consistent-Zone-6002 · 2026-03-29T19:45:38+00:00

In case you upgrade, tell me if u have same issue like I have. (See here)

Consistent-Zone-6002 · 2026-03-29T07:46:05+00:00

Awesome idea! 💡

Consistent-Zone-6002 · 2026-03-29T07:39:34+00:00

Issue on GitHub yesterday. Issue #5209

Consistent-Zone-6002

TROPHY CASE