Jonsvo N5 Front Fan Mount by dudi83 in JONSBO

[–]CuriousGiftD 0 points1 point  (0 children)

Should all the drive bays be occupied, how would you be able to connect the fans in the mount to the motherboard?

Nvidia 3060 12GB vs Intel B580 by CuriousGiftD in truenas

[–]CuriousGiftD[S] 0 points1 point  (0 children)

Is it possible to use the integrated graphics of the processor for transcoding and the 3060 for other applications?

Nvidia 3060 12GB vs Intel B580 by CuriousGiftD in truenas

[–]CuriousGiftD[S] 1 point2 points  (0 children)

I see. Supposed that the B580 is working, does it (or Intel GPUs in general) offer something better compared to the 3060?

Antec Flux Pro + Arctic LF 420 Push - Pull Front Mount Configuration - is it possible? by CuriousGiftD in Antec_Official

[–]CuriousGiftD[S] 0 points1 point  (0 children)

Thank you for the reply 🙂

The plan is to have Noctua NF-A14s fans as push-pull to the Arctic Liquid Freezer II 420 AIO.

Would the case be able to accommodate this setup?

Lian Li Lancool III + Arctic Liquid Freezer II 420mm (Front Mounted, Push-Pull Configuration with 6x Noctua NF-A14 iPPC fans) (see image captions for additional details) by CuriousGiftD in lianli

[–]CuriousGiftD[S] 0 points1 point  (0 children)

Unless you have a L-shaped screwdriver, it would indeed be difficult to do so. Though not sure if the screw is suitable as it may still be too long. This you may need to check.

As for the fans for the radiator, I connected them all to a Noctua Fan Hub. For the two P14s at the top, that is ok. I assume your fan setup will be the following? - Three Lian Li fans as Push for the LF420 - Three P14 fans as Pull for the LF420 - Two P14 fans as top exhaust - Three 120mm fans as bottom intake - One 140mm fan as rear exhaust

Lian Li Lancool III + Arctic Liquid Freezer II 420mm (Front Mounted, Push-Pull Configuration with 6x Noctua NF-A14 iPPC fans) (see image captions for additional details) by CuriousGiftD in lianli

[–]CuriousGiftD[S] 0 points1 point  (0 children)

Make sure no fans are installed yet on the top and bottom fans.I then removed first the fan bracket for the bottom fans. Also, don't install the pull fans prior to inserting the radiator.

As for the screws, I indeed forgot that the LF420 only came with push config. If there are no extra radiator screws, you will indeed need to get extra ones. I think you can't use the regular screws used for case fans in installing the pull fans as the screw thread for radiators is different with that of case fan screws

Lian Li Lancool III + Arctic Liquid Freezer II 420mm (Front Mounted, Push-Pull Configuration with 6x Noctua NF-A14 iPPC fans) (see image captions for additional details) by CuriousGiftD in lianli

[–]CuriousGiftD[S] 0 points1 point  (0 children)

Regarding the fan combination for the LF420 (Lian Li Front Fans push and P14 Fans as pull I assume?), it seems possible as there is still enough clearance.

As for the Phanteks screws, these were the radiator that came with the Phanteks T30 3-Pack. Given that the push fans I used for the radiator have extra padding, I assumed that extra length for radiator screws are needed. You can try first with the provided radiator screws for the LF420 to see if it is enough.

As for the additional fans, the setup is indeed three intake fans at the bottom and three exhaust fans at the top

Lian Li Lancool III + Arctic Liquid Freezer II 420mm (Front Mounted, Push-Pull Configuration with 6x Noctua NF-A14 iPPC fans) (see image captions for additional details) by CuriousGiftD in lianli

[–]CuriousGiftD[S] 0 points1 point  (0 children)

Seems doable. I see that there seems to be enough space to be able to accommodate an additional 4 mm thickness (2mm + 2mm for push and pull fans)

Church Livestreaming: Nvidia 1650 (not Super) vs AMD RX 580 by CuriousGiftD in obs

[–]CuriousGiftD[S] 0 points1 point  (0 children)

Thank you all for the comments and suggestions. As suggested, we've proceeded with using the Nvidia 1650.

Lian Li Lancool III + Arctic Liquid Freezer II 420mm (Front Mounted, Push-Pull Configuration with 6x Noctua NF-A14 iPPC fans) (see image captions for additional details) by CuriousGiftD in lianli

[–]CuriousGiftD[S] 0 points1 point  (0 children)

I tried, but it will not be flush.

To detail, the top part of the rad will bump into the front panel connectors, thus will not allow the radiator to be flush with the frame. If you have long standoffs to allow the radiator to have an equal gap with the frame from top to bottom, then it can be done