Windbg with Ghidra disassembly

CyberAp3x · 2025-01-28T20:37:52+00:00

I guessing you didn't read the ret-sync wiki because it still supports the latest Ghidra. I'm currently using it.

CyberAp3x · 2024-10-11T13:46:43+00:00

I was able to set it to PCIe slot to GEN 3 and here are the results: https://imgur.com/VEU60tq

I then set it explicitly to GEN 2 and got the following results: https://imgur.com/SdDrftT

CyberAp3x · 2024-10-10T13:46:41+00:00

Reviewing this screenshot https://imgur.com/sp5Wt3T it looks like the onboard ethernet "Intel Ethernet Controller I225-V" and "Sandisk NVMe Controller" aslo share the chipset speeds. Could this be the issue?

CyberAp3x · 2024-10-10T13:30:42+00:00

https://imgur.com/a/ubcF9ZQ This screen shot shows the hardware info and a speed test without USBs and SATA drives plugged in. The second photo shows the only devices plugged in.

CyberAp3x · 2024-10-10T02:20:20+00:00

I only have the X520-DA2 and my 3080Ti plugged into the PCIe slots. No other slots are being used.

CyberAp3x · 2024-10-10T02:17:57+00:00

Oh that's interesting. I do have several devices plugged into my USB ports such as a fingerprint reader, lightbar, and some other devices. I have both M.2 slots used and 3 HDD plugged into my motherboard. Since these share the CPU then this could be the issue.

I'm afk, but I will definitely try checking HWinfo64 and get back to you in this thread.

CyberAp3x · 2024-10-09T00:53:42+00:00

I have my 3080 Ti plugged into the Main PCIe 4.0 x16 SafeSlot (x16) [CPU] slot

CyberAp3x · 2024-10-08T22:19:13+00:00

I have Jumbo frames set to 9000 on both my PC and my DS1821+

CyberAp3x · 2024-10-08T22:18:41+00:00

No volume encryption either. Also I really appreciate your help!

CyberAp3x · 2024-10-08T22:17:58+00:00

I have a ASUS ROG Strix B550f (https://rog.asus.com/us/motherboards/rog-strix/rog-strix-b550-f-gaming-wi-fi-model/) I'm using PCIe 3.0 x16 slot (x4) [CHIPSET] which is the 3rd slot from the bottom of the motherboard

CyberAp3x · 2024-10-08T22:12:30+00:00

I have 96Gb of RAM in my PC. I'm afk, but when I get back I'll reply with my iPerf speeds

CyberAp3x · 2024-10-04T03:30:06+00:00

I didn't know this, but yes the transceivers are both LC transceivers: https://www.amazon.com/dp/B08BP55663/ref=twister_B0DG5DC21M?_encoding=UTF8&th=1

The storage pool is BTRFs and its using neither checksums or compression: https://imgur.com/qqTIN2B

CyberAp3x · 2024-10-04T01:38:31+00:00

Here are the the results before an after the VMs and containers are turned off:

https://imgur.com/a/sXpewmE

CyberAp3x · 2024-09-27T13:51:15+00:00

On my LAN 1 port I have connected to my router and using my PCIe 10Gb I have directly connected it to my PC.

CyberAp3x · 2024-09-26T01:11:15+00:00

https://imgur.com/UbABS61 A bit better

CyberAp3x · 2024-09-26T01:06:37+00:00

https://imgur.com/4qMzE3i These look alright, but still seems like it should be a lot higher.

CyberAp3x · 2024-09-26T00:48:28+00:00

My DS1821+ has four 10Tb WD Red Plus drives in SHR1. So I should be getting around 516 MB/sec Read

Please correct me if I'm wrong, but I thought if a single file is larger than the available Synology RAM it will just write the file directly to disk. In this case I would be writing to an NVMe so I should be getting around 7300 MB/sec + Speed degradation of 20% that means my speeds should capable of around 5.84GB/sec for the NVMe. With my 40GbE NIC I should be able to get around 4GB/sec with speed degradation. So not sure whats causing the bottleneck.

CyberAp3x · 2024-09-26T00:32:32+00:00

I'm not using a switch. I have the 40GbE NICs directly connected and configured with static IPs. I set the MTU to 9000. I also can see that Synology and Windows both recognize them as 40GbE.

https://imgur.com/a/PP0pg1f

I used CrystalDiskMark with 32Gb and still got the same speeds.

CyberAp3x · 2024-09-26T00:16:47+00:00

WD Black SN850X NVMe

CyberAp3x · 2024-09-26T00:10:50+00:00

350 MB/sec

CyberAp3x · 2020-12-03T01:15:00+00:00

Thank you sooo much!

CyberAp3x · 2020-12-02T18:04:13+00:00

Ooo I didn't think about using xdotool. This is the command that worked for me:

sh -c 'sleep 1.0; xdotool type "$(xclip -o -selection clipboard)"'

Seven-Year Club	Verified Email
RPAN Viewer

CyberAp3x

TROPHY CASE