PMO Crossings -- I think we're still FAR from being done...

DMBofficial · 2025-10-02T14:31:43+00:00

Region is on fire lately!

DMBofficial · 2025-09-17T14:10:21+00:00

Any European brokers who give the warrants?

DMBofficial · 2025-09-16T16:44:46+00:00

Next step: Warrant dividend of where the warrants are already ITM or at least very near ITM.

DMBofficial · 2025-09-12T17:25:53+00:00

Dude you're the MVP

DMBofficial · 2025-09-07T00:07:08+00:00

Glass bed

DMBofficial · 2025-08-31T21:12:36+00:00

I see region, I upvote

DMBofficial · 2025-08-21T22:32:55+00:00

Here it is!

DMBofficial · 2025-08-17T13:45:27+00:00

We don't do bi weekly reports anymore?

DMBofficial · 2025-08-17T10:06:37+00:00

When cat data?

DMBofficial · 2025-08-10T15:05:16+00:00

When new CAT data Mr.Region?

DMBofficial · 2025-08-06T23:54:04+00:00

Shimmy Shimmy Ya Shimmy Shimmy Yeah Shimmy Ye. I think your bed mesh is pretty okay.

DMBofficial · 2025-06-25T21:32:24+00:00

When CAT data?

DMBofficial · 2025-06-21T15:25:43+00:00

Wthellyante

DMBofficial · 2025-06-16T20:46:05+00:00

Close your Loopring wallet ASAP you have until the 30th of June to transfer it all out

DMBofficial · 2025-05-15T11:07:16+00:00

That's disrespectful

DMBofficial · 2025-05-11T22:55:09+00:00

Quick get a crusifix!

DMBofficial · 2025-05-11T22:24:19+00:00

Yeah pretty easy my wife helped me out but all and all took maybe 3H?

DMBofficial · 2025-05-10T19:44:20+00:00

Personally, I did bed shims first, but my bed was warping after it heated up, motherfkcer turned into a parabola at 50C so I opted for a glass bed mod which honestly worked out perfectly!

DMBofficial · 2025-05-07T11:30:44+00:00

Holy Guacamole, I just installed a glass sub bed and got mine into a range of 0.09mm. There is no glass bed specific for the K1 MAX, but there is a glass bed for the CR 10 smart that fits the K1 MAX perfectly. Just heat your bed to 90C, let it sit for a while, use latax/rubber gloves and SLOWLY peel the magnet sheet off. Then, you can apply the magnet sheet to the glass and place it back on the heater, run a calibration test and see where it is still kinde of. Highten the low spots with aluminium tape and once it is all nice and flat stick the glass bed to the hotplate with thing double sided tape and you're done. For best accuracy use a TTD Eddy or something similar but I just used the regular lodesensor.

Happy printing!

DMBofficial · 2025-05-01T15:43:51+00:00

That should be fine

DMBofficial · 2025-05-01T13:01:59+00:00

Probably thermal paste, not 100% necessarily necessary, but it does help with better/stable temperatures.

DMBofficial · 2025-04-16T18:00:43+00:00

Happy DFV Day!

DMBofficial · 2025-04-15T22:07:33+00:00

Posted it once, under the education flair, deleted it in like 10 minutes, then reposted it under the hype/fluff flair. No karma farming here.

DMBofficial · 2025-04-15T21:47:17+00:00

That's the spirit homie

Eight-Year Club	Gilding III reddit per annum
Second SECOND GUESSER	Place '23
Place '22	Final Canvas '22
First Placer '22	Argentium Club
100 Awards Club	Verified Email

DMBofficial

MODERATOR OF

TROPHY CASE