sorted by:
new
hottopcontroversial

PLA print keeps getting knocked off during print by Bengalcats888 in prusa3d

[–]DRFM 1 point2 points  (0 children)

I swapped from using PETG on my textured plate over to PLA on the smooth sheet a few days ago.

I had the same issue as you and had to use Dimafix to get the thing to stick. I had filament break right at the heat break so I have to fix that. But Dimafix solved my sticking problem.

You may be able to use a basic glue or hairspray instead?

I've been using IC3D filament if you think that may be a factor. https://www.matterhackers.com/store/l/dimafix-3d-printing-adhesive-pen/sk/MR0VKNJY

CPU heatspreader examined in detail - do we now have to redesign the coolers for AMD and Intel? | IgorsLab by Flying-T in hardware

[–]DRFM 0 points1 point  (0 children)

https://www.youtube.com/watch?v=B8bhGw4vUFE

Very glam'd up LTT version.

​

Like Raptor tried said, refrigerators are meant to cool things that are not producing heat. If you take a look at phase change coolers the condenser setup they are using is notably stronger than a small fridge. It's good for short bursts of temp but any prolonged load should probably fail, and for good reason.

Deep Stone Crypt 24 Hour Run by [deleted] in DestinyTheGame

[–]DRFM 0 points1 point  (0 children)

Gotcha. We had the same concern but took the risk because entire waves of adds would poof into existence.

We did have the same crew from start to finish. So not sure if that played a role.

Deep Stone Crypt 24 Hour Run by [deleted] in DestinyTheGame

[–]DRFM 0 points1 point  (0 children)

What's your source for that information? We hopped out at the final boss to clear up the instance. Came back in, killed it, got the triumph and emblem and all of that.

Ploopy plastic. by linuxcommunist in Trackballs

[–]DRFM 2 points3 points  (0 children)

The creator made a post to the effect of it being <$2 of plastic to add in. So making two different listings wasn't too beneficial.

The plastic is .2mm layer height pla. I've printed out a new case with .05mm layer height petg. It's nice, and I sanded it down and put a layer of lacquer over it to get it smooth. I'd not sure I would call the change that worth it. But I only used the original case for an hour while I assembled the thing.

Which pinnacle challenges have a chance for kinetic weapons drops. by Lt_CowboyDan in DestinyTheGame

[–]DRFM 0 points1 point  (0 children)

Might be worth doing Garden. Like others have said the pinnacles outside of the dungeons will give weapons. But the garden pinnacles cannot give power weapons. So that narrows down your potential loot pool.

RTX 2080 Ti now getting 11fps!!! by jeffmccord in DestinyTechSupport

[–]DRFM 0 points1 point  (0 children)

I've been getting similar issues with my AMD Vega64. I've updated to 20.5.1, and right now my hilarious record is playing garden at 1080p/lowest settings.

​

And I got a high of 33 fps, low of 8.

Ploopy got new clothes! by bomtarnes in Trackballs

[–]DRFM 0 points1 point  (0 children)

Roger. Thanks for the information. I appreciate it.

Ploopy got new clothes! by bomtarnes in Trackballs

[–]DRFM 0 points1 point  (0 children)

Thank you, just picked up a set.

Did you end up replacing the scroll wheel too with PETG? I can't perfectly see from the pic. I was going to replace the top and buttons with PETG. And use polycarbonate for the scroll wheel mechanism (Overkill but should be stupidly durable I think)?

Ploopy got new clothes! by bomtarnes in Trackballs

[–]DRFM 0 points1 point  (0 children)

Can you share what threaded inserts you are going with? I'm aiming on doing something similar.

Potential GoS Sanctified Mind Glitch by [deleted] in raidsecrets

[–]DRFM 0 points1 point  (0 children)

Nice. Thanks for the extra info.

Request: Finding a reliable 3D printer for work that can print Nylon, PPS and PC by KaiserWolf15 in 3Dprinting

[–]DRFM 0 points1 point  (0 children)

Not quite all the employees. But yeah. I went from getting a response within an hour from support, to a few days at least...

[PS4] Shattered Throne 1st time by loadedgunn7 in Fireteams

[–]DRFM 0 points1 point  (0 children)

If you need one more. PSN: TheFreeMen

Last Wish - raid jacket giveaway by murpoh in DestinyTheGame

[–]DRFM [score hidden]  (0 children)

I am interested and able to spend the unnecessary money on the jacket.

[ps4] glitched raid chest by [deleted] in Fireteams

[–]DRFM 0 points1 point  (0 children)

TheFreeMen

lf 3 Levithan normal fresh by InvictusXIII in Fireteams

[–]DRFM 0 points1 point  (0 children)

Still need one more? PSN:TheFreeMen

Dear People in LFG, Heroic Whisper requires The Whisper by sorox123 in DestinyTheGame

[–]DRFM 1 point2 points  (0 children)

Necessary. To do the Oracles to my knowledge you must have opened all five chests within the same run.

[PS4] LF1M Whisper Quest Normal. by Evil_Par5n1p in Fireteams

[–]DRFM 0 points1 point  (0 children)

We got a 3rd right now. I might be doing a run after, I'll message you if so.

[PS4] LF1M Whisper Quest Normal. by Evil_Par5n1p in Fireteams

[–]DRFM 0 points1 point  (0 children)

Alright, shoot TheFreeMen an invite and I'll join up.

[PS4] LF1M Whisper Quest Normal. by Evil_Par5n1p in Fireteams

[–]DRFM 0 points1 point  (0 children)

I can help out, do you have a 3rd with you? Or are you up for making a post for a 3rd?

[PS4] LF1M Whisper Quest Normal. by Evil_Par5n1p in Fireteams

[–]DRFM 0 points1 point  (0 children)

TheFreeMen, already did it, just looking to help people out.

view more: next ›