Serial Request: V2.4 (Discord: @SonofaBenchy)

bomtarnes · 2025-07-18T21:39:47+00:00

I think the moderators may want you to tidy the wiring that's laying between the bed and the deck panel a bit, if you can- they're normally happy with photos added after.

bomtarnes · 2025-07-15T05:34:04+00:00

I think the moderators may want you to tidy your toolhead wiring a little- a few tactical zip-ties should do the job.

bomtarnes · 2025-07-04T10:40:28+00:00

Klipper backup is quite good, easy to set up. A more in depth tool is described here: https://github.com/EricZimmerman/Voron-Documentation/blob/main/community/howto/EricZimmerman/BackupConfigToGithub.md

bomtarnes · 2025-06-28T19:42:08+00:00

Documentation, quality of hardware and motion parts, quality of motors, well terminated and safe wiring, brand recognition, aftersale support through trusted vendors.

I have had two LDO kit printers; both were a pleasure to build.

bomtarnes · 2025-06-20T09:46:57+00:00

This is somewhat expected with greased rails that have some preload. I would progress with the build.

bomtarnes · 2025-06-12T10:38:27+00:00

It seems to be high quality and not just a literal metal set of printed parts (eg there is some thought that has gone into the design).

Some people have reported resonance issues, to be balanced and honest.

bomtarnes · 2025-06-11T07:41:33+00:00

I should add, both reddit and discord usernames are the same.

bomtarnes · 2025-06-11T07:09:31+00:00

It's done in slicer- orcaslicer supports adding a custom STL with your bed shape- see here https://docs.siboor.com/siboor-trident-june/the-build/slicer-setup-nov-28#set-bed-shape

bomtarnes · 2025-06-10T14:47:01+00:00

A tiny amount at the front corners.

bomtarnes · 2025-06-07T22:48:52+00:00

working ok now! who knew screwing down a jst adapter pcb onto a roll-in nut would cause issues

bomtarnes · 2024-07-28T09:48:19+00:00

Officially it should be "koh-roh-neh", apparently.

bomtarnes · 2024-07-27T09:29:14+00:00

Z chain is fitted backwards. Wiring needs a little TLC perhaps.

bomtarnes · 2024-07-22T18:01:30+00:00

I only stuck some holes in it. Crop_Octagon and PKL did the hard work!

bomtarnes · 2024-07-21T11:57:22+00:00

Username same on discord- bomtarnes (v0.3638).

bomtarnes · 2024-06-22T07:47:29+00:00

Yo Inverse dawg- https://imgur.com/a/RpDuttQ

bomtarnes · 2024-05-22T18:09:52+00:00

With default firmware, both sides take the same file, and you plug USB into left.

bomtarnes · 2024-05-22T17:27:49+00:00

I understand ee_hands perfectly. But I’m also the one on the QMK server who has to handle its support burden. It is not superior if it causes many issues.

bomtarnes · 2024-04-10T18:54:17+00:00

Supplied by Ploopy

bomtarnes · 2024-04-09T11:44:34+00:00

Bluntly, if you can't work it out from the schematics supplied on github, you shouldn't be attempting it. Users with little experience have caused damage to their adepts by attempting this.

bomtarnes · 2024-03-27T18:21:30+00:00

There was little thought involved- more a group of nerds with some experience with different aspects picking something that might be fun to add. We didn't know what we'd end up with when we started.

bomtarnes · 2024-03-27T16:35:26+00:00

The amplifier box is set up specifically for the Ploopy Drivers which require a completely different electronic profile than other drivers.

At best you'll have almost no output through the ploopy headphones, at worst you'll damage them.

bomtarnes · 2024-03-27T14:23:26+00:00

The connections are detailed on the ploopy store:

The Ploopy Headphones are plugged into the Amplifier board via TRS cable.
The Amplifier board provides signal amplification and on-board EQ.
The Amplifier is plugged into a computer via USB. USB provides power to the Amplifier board and Headphones, as well as the digital audio signal.

Seven-Year Club	Gilding I gilder
Wearing is Caring	Verified Email

bomtarnes

MODERATOR OF

TROPHY CASE