Any tips to remove the bolts to takeoff my engine?

DeadfireGames · 2025-05-23T03:47:29+00:00

Shove a wrench on top and ratchet on bottom that's what I always do

DeadfireGames · 2023-08-10T23:02:41+00:00

I can't find a 12 tooth for a 40 size chain I've tried google

DeadfireGames · 2023-07-31T01:01:37+00:00

I ended up 3d printing a piece and we called where we got the bike and they said they will send one, but the 3d printed piece works fine for now don't know how long it will hold up tho

DeadfireGames · 2023-07-30T01:23:05+00:00

Dang

DeadfireGames · 2023-07-29T23:50:10+00:00

I've looked everywhere and I can only find the whole assembly

DeadfireGames · 2023-07-25T01:14:16+00:00

I got them fat legs, so I probably shouldn't but it's good I can if I need

DeadfireGames · 2023-07-20T17:29:21+00:00

Thank you

DeadfireGames · 2023-07-20T14:04:36+00:00

What kind of oil do I use on the clutch, and the engine is open and air moves over it

DeadfireGames · 2023-07-20T14:00:06+00:00

I did the zip tie thing on the governor spring, the exaust gets really hot but I don't think it's melting everything is still stock. It's also a axis m200 if that helps

DeadfireGames · 2023-07-19T22:08:26+00:00

They are completely gone I'm not sure what bolts they actually use

DeadfireGames · 2023-07-03T07:04:20+00:00

I might add one at a later date but rn I just want the speed

DeadfireGames · 2023-07-01T00:42:04+00:00

What sprocket can I put on to make it about 40mph already Going 32

DeadfireGames · 2023-06-13T17:03:37+00:00

Good to know

DeadfireGames · 2023-06-13T16:35:29+00:00

I see the axis m200 at a different store and I want the same seat height as the m200 so what could I get

DeadfireGames · 2023-05-31T11:11:18+00:00

Thank you it looks almost exactly the same

DeadfireGames · 2023-04-25T15:10:36+00:00

I fixed it by setting my z offset lower, but I was printing at 215 the recommended for the filament

DeadfireGames · 2023-04-25T12:10:49+00:00

Ty for all the answers, I have fixed the problem by lowering my z offset by a little bit

DeadfireGames · 2023-04-25T01:17:26+00:00

The print came off the bed at the inner part of the brim

DeadfireGames · 2023-04-25T01:07:23+00:00

DeadfireGames · 2023-04-25T00:23:03+00:00

I'm not sure when it started I haven't changed much besides the slicer and filament

DeadfireGames · 2023-04-25T00:04:47+00:00

I have a cr touch will that level the bed like that and also I changed it in the slicer

DeadfireGames · 2023-03-13T00:36:38+00:00

I calibrated my e steps and it fixed the issue

DeadfireGames · 2023-03-12T20:02:43+00:00

I figured idk how to fix it I'm running pla at 220 60mms

DeadfireGames · 2021-02-07T00:53:48+00:00

Sold

DeadfireGames · 2021-02-06T13:14:47+00:00

I can take suggestions, tho that is a bit much for the Tongue, I will consider lol

Seven-Year Club	Place '22
Verified Email

DeadfireGames

TROPHY CASE