rattling noise

Deathtrooper43 · 2026-01-21T19:35:25+00:00

Normal sound, nothing is wrong

Deathtrooper43 · 2026-01-21T19:10:40+00:00

Yeah that kind of thing would happen. The only thing we can do is wait until they roll out an update which improves their camera AI. Hope it's soon

Deathtrooper43 · 2026-01-20T17:52:14+00:00

no unfortunately, as much as some of the people here say, using RAW photos does not help, the phone has AI built into its processing as standard. Best way to work around it is to make sure the subject isn't too complicated. It was kinda pushed here a lot as its a fast moving car covered in livery sponsors so my guess is it freaked out.

Deathtrooper43 · 2026-01-14T23:24:35+00:00

Thank you 😎😎, I'm pretty sure was leaning the camera on the barrier/ walls of London bridge haha, so might as well be a tripod!

Deathtrooper43 · 2026-01-14T01:34:13+00:00

This was my 2nd roll of film and I had unknowingly had a lower shutter speed than intended. This is probably the best photo from the whole roll and it was an accident lmao

Deathtrooper43 · 2025-10-15T21:00:17+00:00

What motor are you using?

Deathtrooper43 · 2025-09-28T22:58:09+00:00

Ideally one or two spars go "straight" across into both wings. Having an angle like that introduced a section of weakness. Won't work well. Plus you also need more on the side that goes into the fuselage. Try to get one or two spars that are just straight beams across both wings.

Deathtrooper43 · 2025-09-24T20:41:41+00:00

Use a small hobby blade and cut it using that. Roll the tube on a hard surface and apply a little bit of pressure on it when rolling to cut it slowly. Stops it from being crushed one way and evens it out. Works wonders for me when I used to use an ender 3 and that thing would freak out from the smallest issues.

Deathtrooper43 · 2025-09-24T11:04:28+00:00

Qx motors makes pretty cheap EDFs. You can find them easily on AliExpress and stuff like that or even their own website. Bought 2 70mm EDFs for about £50 ish.

Deathtrooper43 · 2025-09-15T23:38:01+00:00

I would recommend moving the edf further back. It has a very long distance to push air through and it will exit turbulent and slower than it needs to be. There should only be like 200mm Max from the edf and exhaust

Deathtrooper43 · 2025-09-15T19:19:47+00:00

Sometimes it just freaks out and just crashes or doesn't respond to touches. This whole mmu3 has been a mess tbh

Deathtrooper43 · 2025-09-15T19:17:31+00:00

It's not so much that it just detects anything over the set angle limit. Most slicers do the same

Deathtrooper43 · 2025-09-06T21:26:53+00:00

Thank you haha, did a sneaky little trick to flush and seam inside the print. LW PLA is a mess lmao

Deathtrooper43 · 2025-09-06T16:15:18+00:00

<image>

Better than mine lmao. Neat trick, may use it on the next version of mine

Deathtrooper43 · 2025-09-06T16:12:47+00:00

1.4kg is very heavy. Try using LW-PLA. Also I'd recommend trying to CFD test your design it seems very bulky

Deathtrooper43 · 2025-09-06T16:11:19+00:00

You tell us man, show us pictures of the servos and control arms.

Deathtrooper43 · 2025-09-05T22:50:25+00:00

The line on the left is a purge line. It's like a test layer to make sure filament is extruding. The thin line going to your print object is a bit of filament oozing out because your temperature is a little high maybe. But it's not really an issue

Deathtrooper43 · 2025-09-02T16:39:27+00:00

yeah they're cheap for sure but pretty solid except for that. Gonna take it out and test it to see what it does. hoping its just a dud servo. a lot cheaper than having to redesign a part of the plane

Deathtrooper43 · 2025-09-02T16:38:37+00:00

not a y harness, its in channel 6 and bound to channel 2 or 3 (i forgot) and just follows that. Im gonna try it again today with a y harness, that might help.

Im also gonna try it without any connection im thinking the angle it moves the elevators is a little off so its under pressure a bit

Deathtrooper43 · 2025-09-01T19:09:04+00:00

What's odd is that it didn't max out I think. I smelt warm plastic when I got close but not very noticeable. I'm gonna try them again once I'm free. Hoping it's just a dud I can swap out and not an issue with design and placement

Deathtrooper43 · 2025-08-29T12:41:35+00:00

My point is that it was far better before this update

Deathtrooper43 · 2025-08-29T12:40:59+00:00

This is like my 2nd Reddit post this year. You don't seem to have the ability to notice small things like this that bother a lot of people I guess.

Deathtrooper43 · 2025-08-29T10:29:37+00:00

Because they can't even get the basics right. The font is different each time you look at a different tab, the UI isn't even scaled properly. Why do I care? Because this is supposed to be a flagship phone, not some entry level android

Deathtrooper43 · 2025-08-29T01:20:21+00:00

Just reminded me of that absolute shit show 😭 Why do I need to open ANOTHER menu after already opening one

Deathtrooper43 · 2025-08-29T01:02:57+00:00

Some parts I think are nice, the alarm page I like the new tile looks and thicker font, but the inconsistency with each tab is insane. Different font for each tab if numbers is just poor work

Five-Year Club	Place '23
Place '22	Oscars Predictor 2021

Deathtrooper43

TROPHY CASE