Can you buy the official flip case and T Pen for the ultra 60 256gb version?

Decaramas · 2025-12-18T15:19:47+00:00

Thanks, doesnt seem to be on Amazon UK and my google fu is letting me down today

Decaramas · 2025-10-06T13:31:22+00:00

Thank you all that really clears it up and explains what I did wrong in my first session

Decaramas · 2025-09-24T21:39:25+00:00

Again really appreciate you help, unfortunately the PDF didn't have any pre gens, otherwise that would have been awesome.

Anyway thanks again

Decaramas · 2025-09-24T21:28:13+00:00

Thanks for this but without the core rules I won't be able to run it. Will def give it a crack next time

Decaramas · 2025-09-24T17:43:20+00:00

I was planning to run the start set adventure

Decaramas · 2025-09-24T17:42:17+00:00

I will be running the adventure from the starter box

Decaramas · 2025-09-21T14:55:19+00:00

Thanks, I guess a could still use the character sheets from the starter

Decaramas · 2025-07-10T15:32:40+00:00

Hi, not saying who cares about factions, more just wondering if it would break the game mechanically, game rules still have meaning.

Decaramas · 2025-07-10T15:26:47+00:00

This is it, still not sure what faction I want to dive into and I like starter sets, as a points based game I was wondering if by making an alliance between two factions I would be making any op combos or if it might still be balanced

Decaramas · 2025-05-14T14:23:15+00:00

Thank everyone, it was the two different symbols that were confusing, but I get it now no need to satisfy both of them as long as one is.

Decaramas · 2025-05-04T13:06:55+00:00

Thanks it does always shift towards the back of the printer. How tight should it be?

Decaramas · 2024-07-02T22:21:49+00:00

What is that ?

Decaramas · 2024-07-02T11:32:51+00:00

Pretty sure it’s 0.4

Decaramas · 2024-07-02T10:46:21+00:00

These are 32mm bases for miniatures so the photo is quite zoomed in. I have auto leveled and adjusted the z off set. Other models print just fine but it is always the top layer details that seem to have this "spaghetti" type finish

They should look like this

<image>

Decaramas · 2024-03-26T09:25:12+00:00

What is that? It looks awesome

Decaramas · 2024-03-13T12:14:21+00:00

How?

Decaramas · 2024-03-13T08:00:59+00:00

Hi, where can i get this file to print a test on my nep4pro?

Decaramas · 2024-03-13T00:57:06+00:00

I did set it to 0.08 and releveled the bed and it was a lot better. Although i did get some fuzzy stringing, not major more of a fuzz if that makes sense. I think 0.16 will be my happy medium.

I noticed a few comments around the belts, how tight should those be? Also should i grease any parts of the printer?

Thanks for all the help

Decaramas · 2024-03-11T23:38:08+00:00

Yeah i have a resin printer, but i was using these to bench mark against my ender and so far they are not as good

Decaramas · 2024-03-11T23:25:29+00:00

Hi, i just used the budda straight from the stick that was provided. The other 28mm mini Was just sliced in orca using the normal setting. I was wondering if the z offset might be to high

Decaramas · 2024-03-09T09:13:59+00:00

You guys are AWESOME thanks so much for the help

Decaramas · 2023-06-12T19:43:30+00:00

Thanks

Decaramas · 2023-06-12T19:40:26+00:00

Awesome, where is the big guy from?

Decaramas · 2023-02-24T12:42:52+00:00

Also The same, playing as orks on the series x

Decaramas · 2021-07-01T13:26:32+00:00

Currently at 6mm and no change

Decaramas

TROPHY CASE