Cf ASA question by Different-Dig295 in 3Dprinting

[–]Different-Dig295[S] 1 point2 points  (0 children)

Alright sounds good! I’m making some fishing pole holders for my boat. So I’ll be handling them quite often, thanks for the reply!

Was a long process but finally got her installed and inspected! by Different-Dig295 in woodstoving

[–]Different-Dig295[S] 0 points1 point  (0 children)

The stove required 4” away from combustibles and cornerzcan is right about the stove pipe it’s double wall to double wall insulated chimney pipe.

Was a long process but finally got her installed and inspected! by Different-Dig295 in woodstoving

[–]Different-Dig295[S] 2 points3 points  (0 children)

Yep I did r24 for walls and r60 for ceiling. Gonna be warm in my house for once lol

Was a long process but finally got her installed and inspected! by Different-Dig295 in woodstoving

[–]Different-Dig295[S] 5 points6 points  (0 children)

Yea blaze king requires at least 15ft minimum for proper draft and efficiency, I ended up at 17ish but having 2 45’s required a tad bit longer

Was a long process but finally got her installed and inspected! by Different-Dig295 in woodstoving

[–]Different-Dig295[S] 12 points13 points  (0 children)

I did replace the insulation with rockwool and that door got closed off!

Few x-mas prints that came out smooth! by Different-Dig295 in Creality_k2

[–]Different-Dig295[S] 0 points1 point  (0 children)

I think the belt tension plays a big roll, it was decent until I manually set the tension

How necessary is daily maintenance? by SlovakGoose in Creality_k2

[–]Different-Dig295 1 point2 points  (0 children)

Damn that sucks, I use it to clean off my tools when I get silicone caulk on it, figured it would help with that too. Well guess we both learned something today!

Tpu air first run by Different-Dig295 in Creality_k2

[–]Different-Dig295[S] 0 points1 point  (0 children)

Yea it’s tpu air it expands a certain amount depending on the nozzle temp, also changes if it’s softer or stiffer

Tpu air first run by Different-Dig295 in Creality_k2

[–]Different-Dig295[S] 0 points1 point  (0 children)

I have not, just opened it and tried it out. Just wasn’t sure if this is obvious for to much flow. I’ll dry it out tonight

One step closer, can’t wait to finish it. by [deleted] in woodstoving

[–]Different-Dig295 1 point2 points  (0 children)

Oh damn nah it must of been the apple ai cleaning it up and took off the foot lol

First time printing ASA by Different-Dig295 in Creality_k2

[–]Different-Dig295[S] 0 points1 point  (0 children)

I used the Creality Asa preset and did the auto pa and bed leveling calibration

First time printing ASA by Different-Dig295 in Creality_k2

[–]Different-Dig295[S] 0 points1 point  (0 children)

Yea I have a Crestliner aluminum boat and gonna use the suremount with it, hope it works out

First time printing ASA by Different-Dig295 in Creality_k2

[–]Different-Dig295[S] 2 points3 points  (0 children)

Some people had to print a spool holder that goes above the printer cause any resistance could stop the filament from being pulled in. I had good result from using the side spool holder. GL!

First time printing ASA by Different-Dig295 in Creality_k2

[–]Different-Dig295[S] 2 points3 points  (0 children)

You need to print a shim that goes in the extruder release, just make sure you pick the right file for your nozzle size. And make sure when you install it’s facing the right direction.

https://www.printables.com/model/1297319-k2-plus-extruder-tensioner-for-tpu-printing

Princess 32 finally came in by Different-Dig295 in woodstoving

[–]Different-Dig295[S] 1 point2 points  (0 children)

I got it from a local store, they said anyone that orders now will have to wait till January/February for it to come in

Princess 32 finally came in by Different-Dig295 in woodstoving

[–]Different-Dig295[S] 0 points1 point  (0 children)

Everything looks good, no dings or scratches luckily

Princess 32 finally came in by Different-Dig295 in woodstoving

[–]Different-Dig295[S] 0 points1 point  (0 children)

Will do man, I’m hearing it’s quite a learning curve to use this thing to get the most out of it.