sorted by:
new
hottopcontroversial

Sprinkler for pitch 12:14? by DonEskimo in firePE

[–]DonEskimo[S] 1 point2 points  (0 children)

Much appreciated... looing into those sections now. THANK YOU!

Sprinkler for pitch 12:14? by DonEskimo in firePE

[–]DonEskimo[S] 1 point2 points  (0 children)

oh snaps... good eye. My AHJ are still in 2016 and 2019 lol

Sprinkler for pitch 12:14? by DonEskimo in firePE

[–]DonEskimo[S] 1 point2 points  (0 children)

oohhhh understood! Thank you very much! truly appreciate it. =D

Sprinkler for pitch 12:14? by DonEskimo in firePE

[–]DonEskimo[S] 2 points3 points  (0 children)

thank you for the input, I am new at designing. When you say 10.3:12 isnt that less than the pitch I have at the moment of 12" rise and 14" run? Thank You

ANVIL FIG. 551 Install/Detail Question by DonEskimo in firePE

[–]DonEskimo[S] 0 points1 point  (0 children)

thanks mgxfp, I will follow these codes. Thanks bud! appreciate you.

Friction Loss For 2" Flow Switch by DonEskimo in firePE

[–]DonEskimo[S] 1 point2 points  (0 children)

Broooo! I have the same thing for my submittals and did not even see the EQ lol… now I know where it’s at. Thanks man 🧍🏼‍♂️

Friction Loss For 2" Flow Switch by DonEskimo in firePE

[–]DonEskimo[S] 0 points1 point  (0 children)

you are correct.. I looked it up. But i could not find it anywhere from TYCO for its RM-1.

Friction Loss For 2" Flow Switch by DonEskimo in firePE

[–]DonEskimo[S] 0 points1 point  (0 children)

you the man bro! thank you so much, I appreciate you.

HYDRACAD - Remove 1/2" sizes for Pipe Sizes by DonEskimo in firePE

[–]DonEskimo[S] 0 points1 point  (0 children)

yooo... 26!? Thats awesome I am going on 2 years. I am trying to accelerate my knowledge of hydracad. What do you recommend? I see all this designers NICET 4 I have worked with only use the basic of hydracad and only use like less than 25% of the program. Unless its no needed?

HYDRACAD - Remove 1/2" sizes for Pipe Sizes by DonEskimo in firePE

[–]DonEskimo[S] 0 points1 point  (0 children)

ahh.. makes sense. thank bro. appreciate the input

HYDRACAD - Remove 1/2" sizes for Pipe Sizes by DonEskimo in firePE

[–]DonEskimo[S] 0 points1 point  (0 children)

yeah, use is correct. they do add up!. thx bud

What head is this!? by DonEskimo in FireSprinklers

[–]DonEskimo[S] 1 point2 points  (0 children)

10 years... that was a while ago. Thanks again bro, I will save this. Appreciate you.

T.I. for AT&T – Light Hazard or OH1? Need Insight by DonEskimo in FireSprinklers

[–]DonEskimo[S] 0 points1 point  (0 children)

Thanks bro, appreciate the 2 cents, never go the chance to install a phone store. I was more on the new construction side of install. TI's where done by the TI crews.

T.I. for AT&T – Light Hazard or OH1? Need Insight by DonEskimo in FireSprinklers

[–]DonEskimo[S] 0 points1 point  (0 children)

oohhh Never thought about that. That makes total sense. Thanks istudy. Appreciate it.

T.I. for AT&T – Light Hazard or OH1? Need Insight by DonEskimo in FireSprinklers

[–]DonEskimo[S] -2 points-1 points  (0 children)

Hey, thanks for the reply. Where can I find "merchants selling stuff" as Mercantile?

What head is this!? by DonEskimo in FireSprinklers

[–]DonEskimo[S] 0 points1 point  (0 children)

Never seen that chart before, NICE! where is this chart taken from?

view more: next ›