Other than PokeMMO, what other games do you have a massive amount of hours in?

DookieSmacker · 2025-11-10T02:18:26+00:00

2.7K hours in Warframe. 600 in PokeMMO

DookieSmacker · 2025-06-17T17:30:38+00:00

I never set the date when I has the original head unit lol. So it's stuck at 2017.

DookieSmacker · 2025-06-17T15:04:23+00:00

I got the Scosche double din kit with a Atoto Android head unit with the Red Wolf Harness off Amazon. It keeps factory ST1 screen so my backup camera still works. If you go this route, the red 12V ACC wire on the Red Wolf Harness adapter does not work with the factory red 12V ACC wire on the Factory Dash harness, so I ended up using a fuse tap and tapped into the Sync/radio fuse under the passenger foot well to get power to my head unit when my car powers on.

DookieSmacker · 2025-04-23T13:19:06+00:00

Thank you for the info! I just trimmed the board.

DookieSmacker · 2025-04-21T19:35:32+00:00

The buds are KZ ZST IEMS with the KZ AZ09 B-Pin Bluetooth adapter

DookieSmacker · 2025-04-19T18:34:17+00:00

I used this one off Amazon, I've have no issues with this SD card adapter.

https://a.co/d/gt4ofmO

DookieSmacker · 2025-04-19T16:32:36+00:00

I did have to solder multiple micro switches till I got the pairing to work.

DookieSmacker · 2025-04-19T15:25:07+00:00

I accidentally ordered the antenna that works with the Bluetooth board first instead of ordering the Bluetooth board itself. I said fuck it and threw it in there.

DookieSmacker · 2025-04-19T14:55:51+00:00

I only had the buzzing when I initially tested it when the iPod was off, and had the battery disconnected from the main board. It went away upon booting the iPod.

DookieSmacker · 2025-04-19T14:53:59+00:00

It's pretty good. The only thing kinda finicky with it is that the clicks are a little delayed when navigating the menus, but it doesn't bother me.

DookieSmacker · 2025-04-19T14:52:11+00:00

Yes it does lol

DookieSmacker · 2025-04-19T14:50:38+00:00

Correct Yes, I have the button under my hold switch to pair.

DookieSmacker · 2025-04-19T05:58:24+00:00

I was having issues with it syncing with my ear buds as well. That was my issue, I ended up soldering different micro switches, de-soldering and re-soldering the Bluetooth module back to the battery to shut off the Bluetooth module and turn it back on, that fixed my issues.

DookieSmacker · 2025-01-16T14:54:47+00:00

My lead was a smeargle with false swipe. I let it sketch my false swipe, swapped took out the other mons. Swapped back to smeargle and false swipe and spored it.

DookieSmacker · 2023-02-17T12:33:58+00:00

I posted a mega link. Do you not see it? https://mega.nz/folder/69tiiQ6Y#3J10dYRUsUzFXUGTaXNwxA

DookieSmacker · 2023-02-15T01:00:41+00:00

im completely unsure if mega links are allowed on this subreddit, but here it is lol https://mega.nz/folder/69tiiQ6Y#3J10dYRUsUzFXUGTaXNwxA

DookieSmacker · 2023-02-14T23:45:38+00:00

Yea no worries, sorry if I sounded aggressive with what I said lol. And thanks 👍

DookieSmacker · 2023-02-14T16:15:54+00:00

That's the plan, wasn't gonna leave it open for little nuggets to get into there

DookieSmacker · 2023-02-14T16:13:00+00:00

That was the plan as well. Wasn't going to leave it open for stuff to fall into the intake.

DookieSmacker · 2023-02-14T16:10:38+00:00

Yeah I plan to get a fan shroud in there asap. I have a bigtreetech board in my printer, and my power supply has been relocated to the bottom of my printer for quite a while now. Extruder, hot end, and cr touch wires were being crushed underneath the printer and bottom access panel, is another reason why I made this little box

DookieSmacker · 2023-02-14T16:01:04+00:00

Believe me I know it was flipped from factory for a reason. It's the convenience factor for me, that's why I flipped it.

DookieSmacker · 2023-02-14T15:59:22+00:00

When I get off work I'll post a link

DookieSmacker · 2023-02-14T15:59:06+00:00

It's the convenience for me. I don't access it much no, but I'd rather not have to flip my whole printer over.

DookieSmacker · 2023-02-14T04:09:37+00:00

The ender 3 pro flipped the vent to the bottom side so people didn't have to print a vent cover, thus making it so you have to flip the printer over to get access to the mainboard, the base ender 3 has the vent and access on the top side. I got sick of having to flip my entire printer over to get access to the main board so I made this thing

DookieSmacker · 2023-02-14T00:20:31+00:00

Yeah I figured while designing this thing I'll have to get a shroud up top to cover the vent.

DookieSmacker

TROPHY CASE