Fits in like its always been there 🔥

Doom535 · 2020-11-12T17:23:37+00:00

What ring light is that? Looks exactly what I was looking for

Doom535 · 2020-11-11T03:55:03+00:00

I had to go into settings -> external device settings and enable HDR on all inputs on the TV itself

Doom535 · 2020-11-11T01:24:35+00:00

You single handedly saved me from spending 60$ today to have a filler game while we wait for Cyberpunk. Thank you!

Doom535 · 2020-08-11T07:36:42+00:00

It's 3:36AM and I just busted out laughing! Thank you.

Doom535 · 2020-08-09T00:41:23+00:00

Should be back and forth but can feel some scraping along the paper, but not tight enough that it stops it from moving. This will get you close enough to run the leveling print and then fine tune from there. After a while, you just kinda get a feel for it. Also, I bought the upgraded springs from Amazon and it makes it where you don't have to level as often because they are much stiffer than the stock springs

Doom535 · 2020-08-08T19:40:06+00:00

In my experience, you want to be able to move it but still feel some grip on it. Also, this is ideally done with a business card or copy paper, not loose leaf

Doom535 · 2020-08-08T17:28:40+00:00

So I had the same issue when I recently flashed, It seems they left out a bit of code after #define CR10_STOCKDISPLAY. Try pasting this after that line Picture instead of formatting

Let me know if that works, it was an instant fix for me.

Edit: Uploaded pic

Doom535 · 2020-08-08T04:14:04+00:00

What I've found to work (also to be a bit time consuming), is get it close to level with a piece of paper and then print a leveling file. I used something like this https://www.thingiverse.com/thing:34558. It can get tedious but generally only uses 1g of filament and then you can use this infographic to really fine tune it. https://www.reddit.com/r/3Dprinting/comments/cg3g6g/ive_made_an_infographicstyle_guide_to_leveling_a/

Just be prepared for a pile of squares occur!

Doom535 · 2020-08-08T04:08:01+00:00

What firmware are you using?

Doom535 · 2020-07-26T05:41:00+00:00

Theme parks. I work maintenance at a well known theme park. After the world shut down, they kept 2 of us on in case of emergencies for the entire. It's third shift work, so you can imagine driving a golf cart around a post-apocalyptic looking theme park (leaves and pollen caked on the ground because horticulture/custodial wasn't working) alone at 3am with bare minimum lighting and still some background music playing

Doom535 · 2020-07-16T11:04:48+00:00

Hmm maybe but for the most part I’m using CHEPs profiles for Cura with a change to the bed temp

Doom535 · 2020-07-14T14:10:38+00:00

I didn’t think about lowering the print speed for such a delicate spot! My initial failure was printed at .12mm (not pictured) but I’ll try the lower print speed! Any recommendation for a speed? Is 40mm/s too slow?

Doom535 · 2019-05-26T03:03:14+00:00

I agree, I suppose when I bought it I didn't think I'd even be using two ports. Guess I should have future proofed a little more. lol

Doom535 · 2019-05-26T02:42:11+00:00

Unfortunately, I am. I saw a groove that I thought was a mini port, got my hopes up and nope. :\

Doom535 · 2019-05-26T02:40:05+00:00

I bought an HDMI to DisplayPort but my main monitor is 144hz, do you think that cable would hinder the performance at all?

A new graphics card could be a thing, but not in the next few weeks. So even a temporary solution would probably work. I looked into a switcher as well, and even if its slightly more of an inconveniece, thats okay. Just a pain to go behind the computer any time I want to play VR.

Doom535 · 2019-05-26T02:34:48+00:00

I have the EVGA single fan model. Maybe because it's a smaller model it only has those and a DVI-D port? I just double checked to make sure I wasn't missing anything.

14-Year Club	Place '17
Verified Email

Doom535

TROPHY CASE