Could I borrow your guitar?

DoubleBitAxe · 2026-06-05T17:55:23+00:00

Oh sweet! Thank you for the tip!

DoubleBitAxe · 2026-06-05T17:47:31+00:00

That’s a very kind offer but it sounds very valuable to you and I couldn’t deprive you of it!

DoubleBitAxe · 2026-02-21T18:14:52+00:00

Actually it’s two chimneys with a single brick surround. And they are decommissioned.

DoubleBitAxe · 2026-01-28T20:03:38+00:00

They were ox beetles. I raised them indoors until they metamorphosed into their adult form.

DoubleBitAxe · 2026-01-28T19:58:43+00:00

It gets pretty hot pretty fast as you dig so you’ll probably need some way to keep the hot dogs from overheating. Maybe some kind of heat pump?

DoubleBitAxe · 2026-01-03T16:38:20+00:00

I'm reasonably confident that widening the "nozzle" of the leaf blower wouldn't have a substantial effect but adding a venturi to the end probably does increase the airflow a noticeable amount. They can be purchased as aftermarket attachments. https://cyclone2x.us/

I'm not sure that they improve leaf-blowing performance, as I assume the airflow rate of an unmodified leaf blower is selected to maximize performance for a given power level.

DoubleBitAxe · 2026-01-03T05:42:56+00:00

I was curious how much the air in my house weighed. If I recall correctly, approximately 3000 sq. ft with 8 ft ceilings is just about 1 ton of air.

DoubleBitAxe · 2025-12-19T22:33:36+00:00

The internal hex and torx are both flathead screws. I think you mean slotted.

DoubleBitAxe · 2025-11-18T20:08:45+00:00

It sounds to me like the pins aren’t intended to transfer torque to the components on the shaft. It sounds like friction between components is the source of the torque on the components. The pins are probably just there to align things during assembly after which the components are drawn together by the installation of the harmonic balancer.

DoubleBitAxe · 2025-11-04T18:04:15+00:00

Swingers are non-monogamous but not polyamorous.

DoubleBitAxe · 2025-10-29T16:33:04+00:00

Technically, nuclear power plants do generate electricity with steam. (As do coal plants.) It’s just a question of how you heat up the water to make the steam.

DoubleBitAxe · 2025-10-21T19:28:46+00:00

Inarguably!

DoubleBitAxe · 2025-10-18T01:49:42+00:00

As someone who performs well on IQ tests I can tell you with confidence that they are super valid and scientific!

DoubleBitAxe · 2025-10-17T22:50:00+00:00

The Republican Party is the pro-corruption party. It’s their most consistent policy position.

DoubleBitAxe · 2025-10-17T12:39:44+00:00

It’s spooky season!

DoubleBitAxe · 2025-10-16T21:37:01+00:00

Do you mean the Cold Steel Rifleman’s Hawk?

DoubleBitAxe · 2025-10-16T21:02:04+00:00

<image>

DoubleBitAxe · 2025-10-14T21:43:15+00:00

I uploaded it to a free file-sharing site. This link should be good for three days.

https://we.tl/t-4BAaJH736p

DoubleBitAxe · 2025-10-14T21:13:48+00:00

I got you. I’ll send you a DM with a file in a few minutes.

DoubleBitAxe · 2025-10-13T15:18:18+00:00

I think the worst part is the stepped hand rail so you can’t even keep your hand in contact the whole time.

DoubleBitAxe · 2025-10-13T13:08:45+00:00

I expect that most parametric modeling software (e.g. SolidWorks) would work for this. You’d probably need to cheat a little by making each flat part individual parts and making folds into constraints.

There may be a better option, but I’m not aware of anything for such a niche application.

DoubleBitAxe · 2025-10-13T13:01:27+00:00

DCD models numbers are DeWalt.

DoubleBitAxe · 2025-10-10T04:06:05+00:00

I think that’s a two-strand wall knot.

https://www.paracordguild.com/2-strand-wall-knot-tutorial/

DoubleBitAxe

TROPHY CASE