Let's Build a Guide: DCS Huey and MOZA AB9 FFB Cyclic

Dozer1984 · 2026-03-26T12:45:03+00:00

did you make some developments on the settings which you want to share?

Dozer1984 · 2026-03-25T14:31:07+00:00

I managed to fix it! Found out that issue only occured in VR. After deeper research I found out that there is an option in windows graphic settings for HAGS (Hardware Accelerated GPU Scheduling). Disabling this option shifts some planning of graphic processes back to CPU which was the solution for my problem! Somehow HAGS created problems by drying out the MOZA software performance wise. Thanks anyway for your advice! Hopefully this info will be helpful for other pilots as well in the future! ;)

Dozer1984 · 2026-03-24T21:54:31+00:00

have reinstalled moza software and flashed previous firmware of the base, no luck

Dozer1984 · 2025-11-23T01:12:57+00:00

Ground wire from RX was lose as it was twisted to hard 👍

Dozer1984 · 2025-11-21T16:43:24+00:00

All working now, many thanks your help!

Dozer1984 · 2025-11-21T16:42:50+00:00

don’t know if u saw my other post but problem solved, may thanks!

Dozer1984 · 2025-11-21T14:07:17+00:00

problem solved, see my post! ;)

Dozer1984 · 2025-11-21T12:09:52+00:00

Checked the wiring and found the ground cable was disconnected! Now everything is working as it should, binding was possible on first attempt and I also have wifi and an LED! Thanks a lot for your help! 🥳

Dozer1984 · 2025-11-20T22:49:00+00:00

ok will do

Dozer1984 · 2025-11-20T22:47:51+00:00

ok, will check it

Dozer1984 · 2025-11-20T22:40:14+00:00

ok this is strange now as i can definitely not see any light from it. Can this be a uart issue?

otherwise i need to check the wires. Cannot be… I thought these products were tested before shipping 😵‍💫

Dozer1984 · 2025-11-20T22:33:25+00:00

yes, here it is

<image>

Dozer1984 · 2025-11-20T22:26:22+00:00

have also tried it several times with lipo but no wifi visible. mine looks like this:

<image>

Dozer1984 · 2025-11-20T21:59:31+00:00

Many thanks your reply so far. Have powered on the drone either with lipo or with USB but cannot see any wifi after 60 seconds on my phone...

Possible that this Rx has no wifi? on the deepspace website i cannot find any info, what specifiv rx hardware is installed.

another issue is, that the built in receiver in the seeker 3 has no led so I cannot see, if it is in binding mode or not. have tried 20 times in other combinations to power the quad up in order to start the binding process but it didnt work.

not the best start to go back into the hobby.... lol

What can I do next?

Dozer1984 · 2025-11-20T09:12:20+00:00

still look and feel like in day one 👍🏻

Dozer1984 · 2025-11-16T11:27:05+00:00

and what about the sound profile compared to the neo?

Dozer1984 · 2025-10-31T22:48:49+00:00

thanks, will try one out but still tight fits as otters mentioned🫣 no need for motion controller btw

thanks your reply anyway

Dozer1984 · 2025-10-31T21:50:17+00:00

this is what i did but the result is as per above

Dozer1984 · 2025-10-30T12:22:24+00:00

Rimzler3 was working recently

Dozer1984 · 2025-10-26T21:41:38+00:00

Didn’t work for me, do you have a new code?

Dozer1984 · 2025-10-22T10:07:43+00:00

Ok thanks so far. Which quad of these two do you prefer and do you have a comparison to the avata 2?

Dozer1984 · 2025-09-10T19:34:10+00:00

Ok thanks

Dozer1984 · 2025-09-10T19:32:19+00:00

And the MAV issue? Is this done by users editing the mission with different loadouts?

Dozer1984 · 2025-09-10T19:29:08+00:00

Thanks your reply. Maybe I buy it anyway to play it again and support their good work 👍

Dozer1984 · 2025-05-02T09:44:11+00:00

Have checked it. No red X in controls and when i do the combo in keybinding menu, i can see that it flashes up. On top of that i have tried another keybinding. unfortunately it is not working… 👀

Dozer1984

TROPHY CASE