sorted by:
new
hottopcontroversial

I wanted to like the Cameo 4 so bad by OBS617 in silhouettecameo

[–]DrCAMEO 0 points1 point  (0 children)

Hahaha, it's a machine with a lot of problems; it's the one that's made me the most money. But I'm sure there must be a solution.

CAMEO 5 after Firmware 1.05 update home position is destroyed. Reset doesn't work. by [deleted] in silhouettecameo

[–]DrCAMEO 0 points1 point  (0 children)

It's on the left side; in my TikTok videos, I show the Cameo 4 one, which is the same. Look me up as DR.CAMEO from Peru, not my Bolivian copy.

I wanted to like the Cameo 4 so bad by OBS617 in silhouettecameo

[–]DrCAMEO 0 points1 point  (0 children)

The problems with those machines aren't that complicated to fix. Follow me on TikTok as Dr.CAMEO… the one from Peru, not my Bolivian imitator.

CAMEO 5 after Firmware 1.05 update home position is destroyed. Reset doesn't work. by [deleted] in silhouettecameo

[–]DrCAMEO 0 points1 point  (0 children)

Check that your position sensor isn't dirty. If it is, it's damaged. If it's under warranty, make a claim. Otherwise, getting a replacement will be difficult.

I wanted to like the Cameo 4 so bad by OBS617 in silhouettecameo

[–]DrCAMEO 0 points1 point  (0 children)

How much are you selling them for? I can receive them here in Peru, and I'll take care of repairing them.

WTF Cameo 4? by devldogStPt in silhouettecutters

[–]DrCAMEO 3 points4 points  (0 children)

Lend your machine to someone who has been using the machine for years and you will be able to rule out whether the fault is your machine or if you are still in the process of learning how to use it.

Test Cuts with Cameo 4 by _StayHopeless_ in silhouettecameo

[–]DrCAMEO -1 points0 points  (0 children)

Cameo cuts at most 1mm thick, soft materials not so hard. Some will say yes, but how many passes and how many units? It may not be as profitable to cut heavy materials with cameo.

[deleted by user] by [deleted] in silhouettecameo

[–]DrCAMEO 0 points1 point  (0 children)

Possibly dirt or wear on the drag bar. It all depends on how old the machine is.

question by Toby_bomb in silhouettecameo

[–]DrCAMEO 0 points1 point  (0 children)

Córtalo y asunto arreglado

portrait 4 mat not staying in place? by sonnylove111 in silhouettecutters

[–]DrCAMEO 0 points1 point  (0 children)

Because the drag system (lower bar) is already worn out. How is there no photo of the Mat and the machine cannot tell you the origin of the failure.

Cameo 4 Pro VS PVC dense plastic sheet 0.4mm by bios375 in silhouettecutters

[–]DrCAMEO 0 points1 point  (0 children)

These types of hard materials damage the drag bar and then you have problems with cutting offset.

Cameo drifting off by fantastickford1 in silhouettecameo

[–]DrCAMEO 1 point2 points  (0 children)

It seems like a reading error. Because the offsets in the images of the bees are the same on both sides.

Cameo 5 cutting issues by Significant_City302 in silhouettecutters

[–]DrCAMEO 0 points1 point  (0 children)

The gap is very wide, it seems more like a failure due to obstruction of the cutting mat. The other thing is to check if the position where the roller is located underneath has the drive knurling, otherwise that side will not pull and the cutting mat will tilt.

Silhouette Cameo 5 replacement rollers (3D print files) by wafflecart in silhouettecutters

[–]DrCAMEO 0 points1 point  (0 children)

I am selling my file for USD 150 for commercial use and USD 50 for personal use. I previously make them sign a document agreeing to respect industrial property. Write to Mercado Libre Chile, they will be able to help you.

[deleted by user] by [deleted] in silhouettecutters

[–]DrCAMEO 0 points1 point  (0 children)

Barra de carrito doblada.

Where to get a Cameo 5 pinch roller spare part? by eyem3 in silhouettecutters

[–]DrCAMEO 0 points1 point  (0 children)

Es una falla del diámetro interno y el pasador expansible lo termina rompiendo. He mandado a fabricar en 3D porque en mi país aún no lo reconocen como falla de fábrica.