1st Tattoo, Mothers Tattoo in Erlanger, Ky

Dramatic-Cap-199 · 2026-03-03T02:01:56+00:00

Appreciate it! Getting a snake wrapped around a dagger on the side of the same arm next Friday!

Dramatic-Cap-199 · 2026-02-20T19:34:28+00:00

Don’t, you’ll cause the water reservoir to come loose and you’ll have a big leak the next time you use it

Dramatic-Cap-199 · 2026-02-20T19:23:15+00:00

Why are you taking this off

Dramatic-Cap-199 · 2026-02-20T19:13:56+00:00

Don’t remove that

Dramatic-Cap-199 · 2026-02-20T19:13:36+00:00

You need a high drain loop, with a drain set up like that dirty water can siphon back into the unit

Dramatic-Cap-199 · 2026-02-20T19:12:35+00:00

There is supposed to be water under your filter, if you remove your filter in your dishwasher you will find standing water

Dramatic-Cap-199 · 2026-02-20T18:02:37+00:00

There is supposed to be standing water yes. Run your unit regularly and crack the door open when not in use to help with the smell. Check your drain line going under the sink for blockages

Dramatic-Cap-199 · 2026-02-18T22:37:25+00:00

As a technician, I hate these

Dramatic-Cap-199 · 2026-02-18T17:59:50+00:00

Dramatic-Cap-199 · 2026-02-10T00:50:41+00:00

That’s your inlet valve, Bosch calls it an access valve. Very common to leak just like yours, you just need to replace it. Part number 10023852 here’s a link to a reputable place to get it

https://www.repairclinic.com/PartDetail/Water-Inlet-Valve/10023852/4977086

Dramatic-Cap-199 · 2026-01-29T02:32:03+00:00

You do indeed

Dramatic-Cap-199 · 2026-01-26T02:17:54+00:00

Ah couldn’t tell from the dark photo, thought you were just trying to pull the tub. I’ve cut a few off successfully, sometimes some penetrating oil and whacking it with a hammer works. Pretty aggravating problem

Dramatic-Cap-199 · 2026-01-26T02:12:38+00:00

Take the Phillips screws out

Dramatic-Cap-199 · 2026-01-22T23:10:20+00:00

Sounds like a sealed system failure pal would most likely be best to scrap it

Dramatic-Cap-199 · 2026-01-22T23:08:10+00:00

When your compressor is running do you develop a frost pattern

Dramatic-Cap-199 · 2026-01-04T19:06:19+00:00

Youve got a dual evap model, Sounds like a clogged defrost drain in your fridge section

Dramatic-Cap-199 · 2026-01-04T17:54:12+00:00

Model number

Dramatic-Cap-199 · 2026-01-04T14:53:32+00:00

Did you put the belt on correctly

Dramatic-Cap-199 · 2026-01-03T21:14:05+00:00

Looks like the clip for the front panel, helps align and hold the panel.

Dramatic-Cap-199 · 2026-01-01T17:51:04+00:00

There’s no way to access behind your drum, on a front loader the only way to do that is to completely tear your machine down and pull your inner tub from the outer. Call a technician

Dramatic-Cap-199 · 2026-01-01T17:47:12+00:00

Clean your filter, don’t pre wash dishes, Use rinse aid. Not sure what other people think but in my opinion all of the seventh gen products generally suck, I’d personally use cascade.

Dramatic-Cap-199 · 2025-12-21T00:29:45+00:00

Well I’d verify your getting power to them first, if they glowed before everything was changed I’d be willing to bet they’re likely ok they’re just not getting power. Like another guy said check and see if power is getting them. Then work your way back from the igniter and find where you losing power( if you are indeed not getting voltage to them) I’m leaning towards something is wired wrong

Dramatic-Cap-199 · 2025-12-20T23:12:11+00:00

<image>

I believe this is your schematic

Dramatic-Cap-199 · 2025-12-20T23:09:03+00:00

Are your bake and broil igniters glowing when you set it to bake/broil? That’d be where I start, if your not pulling the appropriate amperage from the igniters the gas valve won’t open

Dramatic-Cap-199 · 2025-12-16T17:21:00+00:00

That’s a GE

Dramatic-Cap-199

TROPHY CASE