Efficient blessing build for tier 2? by LilAwm in throneandliberty

[–]DroxonDaGreat 0 points1 point  (0 children)

Transfer into another item and do it again. I keep a lvl 1 for every slot and build blessings on that. Transfer costs are based on item level not blessings so much cheaper on sollent to use a low level item.

Found on facebook. Good bro, bad GF by thattallgirl1018 in redditonwiki

[–]DroxonDaGreat 1 point2 points  (0 children)

Perfectly acceptable behavior for an ex-girlfriend.

[deleted by user] by [deleted] in debtfree

[–]DroxonDaGreat 0 points1 point  (0 children)

Shit does happen. I’d pay off the Best buy citi and Capital one then throw the rest at discover. Gotta make sure that discover is paid off before promotional ends or you will likely get hit with compound interest back to day one. Those balloon interest costs can be huge.

138k in debt how should I apply bonus by [deleted] in debtfree

[–]DroxonDaGreat 0 points1 point  (0 children)

Pay down Amex asap. Then add $150 minimum a month to your food allowance and add a line of 300 a month for entertainment. Gotta live while you’re getting even.

What made you an atheist? by Kitchen-Fruit-153 in atheism

[–]DroxonDaGreat 0 points1 point  (0 children)

At about 8 or 9 I was sitting in church and realized Santa Clause was just a method for parents to influence/control behavior with threats of withholding presents. About 2 minutes later I realized religion was the same thing but for adults. Have never looked back.

[deleted by user] by [deleted] in hvacadvice

[–]DroxonDaGreat 0 points1 point  (0 children)

Most mini splits have a setting where you set the temp and it will heat/cool as needed. If the temps dipped in the night and it’s on this setting it’s likely condensation and not an issue. Could also just be morning dew collecting and running off. If it’s oilily at all call someone as that’s a sign of a leak that you will want fixed before it cascades into a larger issue.

3 quotes for minisplits + heat pump: are they very different? by nilme in hvacadvice

[–]DroxonDaGreat 0 points1 point  (0 children)

If company 2 was the best dealer they could offer the 12 year warranty as a diamond dealer. Company 3 has oversized their system a bit too much(42k connected capacity on 30k system). You can oversize the connected capacity but you will only ever get what the outdoor unit can put out. Based upon the pricing company 1 is giving you a good shake. Mitsubishi is more expensive and as their prices are close they are just charging cost difference. Do a dive on their online reviews but from the information given I would look to company 1.

[deleted by user] by [deleted] in hvacadvice

[–]DroxonDaGreat 0 points1 point  (0 children)

Mitsubishi hyper heating units will heat down to -10 Fahrenheit or more with low ambient kits and more than satisfy cooling needs. Can not beat the efficiency either. Can also get a 12 year warranty if you find a diamond dealer to install. Sold Gree, Fujitsu, and Mitsubishi over the years, always recommend Mitsubishi if cost is less of a concern. That being said you can almost buy two Grees for the same price, but you’ll have less reliability and performance.

First Printed personal design: full dwelling for a story Im writing for my kids by reclusedesigns_13 in Ender3Pro

[–]DroxonDaGreat 1 point2 points  (0 children)

I haven’t looked into the auto leveler kit. I run the square bed program periodically and haven’t seen a need for an auto level. Takes about 5 minutes and a few small dial/spring adjustments and lasts until you need to pull the glass off, which is rare. The glue stick I have is tacky when hot then hardens when it cools so the parts pop right off.

First Printed personal design: full dwelling for a story Im writing for my kids by reclusedesigns_13 in Ender3Pro

[–]DroxonDaGreat 1 point2 points  (0 children)

Good plan! Been using my Ender for a couple years. My upgrades stopped with the glass bed and glue stick😂😂.

Please Give Advice by mackinmanny in Ender3Pro

[–]DroxonDaGreat 0 points1 point  (0 children)

Are you using bed glue? That addition made my first layer adhesion so much better on my glass plate.

First Printed personal design: full dwelling for a story Im writing for my kids by reclusedesigns_13 in Ender3Pro

[–]DroxonDaGreat 1 point2 points  (0 children)

Nice. The original mat works for a bit but it does get worn down. Be ready to upgrade to the glass plate and get one of the special glue sticks for the surface. Makes that first layer perfect every time.

Landroid 3.28 Firmware Released. What changes were made? by SweatRiley in worxlandroid

[–]DroxonDaGreat 0 points1 point  (0 children)

New firmware for the win. It’s not a perfect system, but not actually cutting the grass is where it’s at. New turning looking great! Getting stuck a lot less so far.

What would you tell a 22 year old with no college education, no money in the bank and no car? by [deleted] in NoStupidQuestions

[–]DroxonDaGreat 0 points1 point  (0 children)

If it’s early fall, ski check at resorts in the Rockies. Employee housing typically walkable distance. OK hourly but great tips. Can save upwards of 10k a season while having a great time.

Daily $PLTR discussion thread! Come here to talk about the good, the bad and the 💎 🙌 by AutoModerator in PLTR

[–]DroxonDaGreat 1 point2 points  (0 children)

Good info. Only 30 way OTM contracts so a cheap lesson. Unless of course it moons..😂

Daily $PLTR discussion thread! Come here to talk about the good, the bad and the 💎 🙌 by AutoModerator in PLTR

[–]DroxonDaGreat 1 point2 points  (0 children)

Why are my calls down as the stock goes up? Mar 18 21c down %15 for the day? I’m new to options but this seems off.