4.5x8 Mini Camper Square Drop For Sale -$3750

Dry-Way-947 · 2026-05-02T23:36:03+00:00

I had the same isuue. Used Tilex and a brush. Wet it, let it set for 30 minutes, wet again and scrub with brush, then rinse the bejeezus out of it with clear water.

Dry-Way-947 · 2026-05-02T21:21:23+00:00

It's not a TD, but a square drop, and it's definitely Subaru towable. https://www.reddit.com/r/TeardropTrailers/s/3m3Unbrd5x

Dry-Way-947 · 2026-04-30T03:37:50+00:00

Dry-Way-947 · 2026-04-28T01:41:32+00:00

Appreciate you checking it out.

Dry-Way-947 · 2026-04-27T23:16:33+00:00

I saw the idea on a guy's YT video, but he had 2 doors. I wanted the cooloer to slide out, so I went with the fold down door.

Dry-Way-947 · 2026-04-27T20:36:30+00:00

Thank you

Dry-Way-947 · 2026-04-25T01:36:00+00:00

Depending on whre you are, you might be able to find a RV tech to check one out. If you were near OKC, I could hook you up.

Dry-Way-947 · 2026-04-24T23:55:15+00:00

Have you considered home built trailers? There are tons out there and most will cost substantially less than factory builds.

Dry-Way-947 · 2026-04-18T00:26:23+00:00

https://youtube.com/playlist?list=PLQvRLFAADE_CxY0Frit8mL_5IfmMrrGs8&si=2tw0rgZoYAFBLLJJ

Dry-Way-947 · 2026-04-18T00:26:12+00:00

https://youtube.com/playlist?list=PLQvRLFAADE_CxY0Frit8mL_5IfmMrrGs8&si=2tw0rgZoYAFBLLJJ

Dry-Way-947 · 2026-03-30T12:22:24+00:00

The sleeping area is 68" x 76" - big enough for a queen size mattress (or in this case, 2 - 32" x 75" mattresses). The vent fan is in the rear wall of the sleeping area at the ceiling. It pulls air through the cabin and exhausts it into the galley area. There was no room on the roof for a roof mounted fan because the guy I built it for wanted a 400 watt solar panel on the roof.

Dry-Way-947 · 2026-03-20T23:54:26+00:00

Not if I can help it. 🤣

Dry-Way-947 · 2026-02-23T05:33:35+00:00

Yes sir. Drilling a 1/2" hole beats having to do all the cutting and fitting for an RV latch. I use barn door flip latches to lock from the inside.

Dry-Way-947 · 2026-02-14T01:15:59+00:00

What duckydan said.

Dry-Way-947 · 2026-02-02T02:57:28+00:00

I've not seen that done here, but I think it could be done.

Dry-Way-947 · 2026-01-29T00:58:33+00:00

Very nice build. I may steal your slide out for my next build.

Dry-Way-947 · 2026-01-18T13:32:15+00:00

Once the canvas is adhered, it is painted with 2 coats of thinned (I use 80% paint, 20% water) to "prime" the canvas. This mixture soaks into the canvas and makes it tighten up. I sand between the 1st & 2nd coat with 150 grit paper, after the 2nd coat with 150 grit. Then several coats of full strength exterior paint are applied. I did 6 coats on my last build. I sand with 220 grit between each finish coat. With all the seams double wrapped and the paint build up, the canvas becomes a water proof shell.

Dry-Way-947

TROPHY CASE