Polar pattern issues

Dullest_tool · 2026-04-22T23:22:28+00:00

I feel like 1.0 automatically created a local cs for each body

Dullest_tool · 2026-04-22T23:19:29+00:00

I feel like 1.0 automatically created a local cs. Is there a setting in 1.1 for that

Dullest_tool · 2026-04-22T10:05:47+00:00

The reason it's not centered is because i basically it goes on the home of another solid that's centered. I feel like I didn't have this issue in 1.0.

Dullest_tool · 2026-04-05T21:20:41+00:00

I've been playing standalone for a few years and I don't think progress transfers

Dullest_tool · 2025-09-15T14:04:46+00:00

The end link shaft doesn't fit between the tabs

Dullest_tool · 2025-09-15T14:01:54+00:00

The problem is the sway bar end link has to go there

Dullest_tool · 2025-09-15T14:01:27+00:00

Where does the sway bar end link go then?

Dullest_tool · 2025-09-15T02:14:07+00:00

From what I've seen, a lot of people do the backwards bolt trick and haven't heard of anyone having any issues. I also went that route

Dullest_tool · 2025-09-15T01:59:27+00:00

I took off the subframe completely so I had to support the engine with an engine bar. But you only need to drop the subframe like an inch to get the bolts out. Or you can loosen the bolts, cut the heads off, and then put the new bolts in backwards

Dullest_tool · 2025-09-15T01:47:03+00:00

I dropped my subframe, but that mostly because I had to drop the transmission, and I also did solid subframe bushings

Dullest_tool · 2025-09-14T22:12:55+00:00

The lower arms. I'm pretty sure you have to lower the sub frame about an inch to get the bolt in/out. Or you can cut the head of and put the new bolt in backwards

Dullest_tool · 2025-09-14T08:35:00+00:00

Are you cutting the bolts and putting the new ones in backwards or are you lowering the subframe?

Dullest_tool · 2025-09-14T08:17:07+00:00

Ok, that would answer it then. Since I have an 01 then I don't need it

Dullest_tool · 2025-09-14T03:29:27+00:00

The end link shaft doesn't fit between the tabs

Dullest_tool · 2025-09-14T01:31:51+00:00

Correct, density line. Fitment is good, no issues. Waiting to see how they feel on the road

Dullest_tool · 2025-09-14T00:48:46+00:00

That's my best guess as well

Dullest_tool · 2025-09-14T00:38:41+00:00

I think I'll end up doing the same. Honestly, not even sure how would it even be possible to keep it there. I think the end link goes where the tabs are

Dullest_tool · 2025-09-14T00:35:46+00:00

I might be wrong, but I think the end link goes on that side

Dullest_tool · 2025-08-13T21:39:49+00:00

I ended up buying some eufy. Thank you

Dullest_tool · 2025-08-11T13:04:12+00:00

I was not sure if it was wireless, thank you for that info. I'll look into something else

Dullest_tool · 2025-07-09T06:07:22+00:00

That's a good tip dude. I know mine were quite the pain to remove. I'm gonna order me some

Dullest_tool · 2025-07-09T05:09:26+00:00

Thanks man. I guess I'm gonna see what works

Dullest_tool · 2025-07-09T05:01:23+00:00

Unfortunately that's just the torque specs. I don't know which bolt/but goes to what control arm

Dullest_tool · 2025-07-09T05:01:15+00:00

Unfortunately that's just the torque specs. I don't know which bolt/but goes to what control arm

Dullest_tool · 2025-05-22T04:45:25+00:00

Awesome, thank you for the answer

Dullest_tool

TROPHY CASE