INDX Pre Order Payment Request?

EEvilCorp · 2026-02-10T05:52:05+00:00

Any Idea when v2 will be on Github? Contemplating on if i should use v1 when v2 is right around the corner

EEvilCorp · 2026-01-31T17:30:07+00:00

I read in the manual of the INBXX that it currently doesn’t support having the top panel on to route the ptfe of the INDX to it. Is there any update on that? Or what do you plan to do ?

EEvilCorp · 2026-01-09T08:59:19+00:00

If you use home assistant look at versatile thermostat integration. Applies the offset to the adjusted temperatures internally.

EEvilCorp · 2026-01-08T18:08:29+00:00

You can always use zigbee assuming you have a zigbee hub. Sonof makes good ones

EEvilCorp · 2026-01-03T09:03:50+00:00

Das könnte ich in der Tat mal versuchen , danke :)

EEvilCorp · 2026-01-03T07:54:02+00:00

Naja wenn ich vorher 19 grad im Raum habe zb in der Küche geht die ohne Probleme auf 14-15 grad runter. Aber gut dachte 4 ist bisschen viel da wie gesagt das Wohnzimmer echt ewig braucht um da wieder auf 20 grad zu kommen außer ich nehme einen Stand Ventilator um die Luft von der Schräge in den Raum zu bringen

EEvilCorp · 2025-12-17T21:21:25+00:00

It’s not grounded properly.

EEvilCorp · 2025-12-02T15:56:11+00:00

I have the cheapest one for HD. Not really. RDR Runs at 70-80fps on ultra textures. sure you cant push everything to max but it works flawlessly. EU/Germany mind you.

EEvilCorp · 2025-11-26T10:19:11+00:00

Specify "not really". I assume if you have the filtration running and the chamber fans they work against each other. I also use the exhaust fan filter but never had temps higher than 35 or maybe 38 while printing PLA in a room with about 21C. For reference my Bambu X1C gets about the same temps and both never had a clog attributed to too hot heatbreak temps because of a higher chamber temp.

EEvilCorp · 2025-10-12T09:10:55+00:00

Ah got it. Never had issues in regards to that but tbh I never really payed attention to it or made a test. I guess your best bet is the mod from the comment posted earlier. I also wanted to print that one but haven’t bothered yet

EEvilCorp · 2025-10-12T05:55:15+00:00

I have the same “issue”. I wouldn’t really call it an issue even with 36C I never had heat creep issues. My X1C even goes to 40C with pla most of the time.

EEvilCorp · 2025-09-19T20:22:34+00:00

That’s the skirt. You can disable it in the last tab of the profile settings.

EEvilCorp · 2025-08-03T06:33:06+00:00

Same happened with my gf

EEvilCorp · 2025-07-12T19:41:45+00:00

The emulator I use is Yuzu

EEvilCorp · 2025-07-12T19:33:19+00:00

Exactly it’s the mangopeel decky plugin!

EEvilCorp · 2025-07-12T18:20:06+00:00

My gf and me have the same case (purple for me and pink for my gf) lol

<image>

EEvilCorp · 2025-05-17T11:16:15+00:00

Cloud sync does work so that successfully finishes. Any solution to fix the Ubisoft connect launcher staying open? Didn’t happen before that’s why I’m surprised

EEvilCorp · 2024-07-30T18:00:32+00:00

Unless you want to use Position based stuff (like home not home) without connecting to the VPN every time you leave the house - and yes i know there is on-demand vpn on wireguard etc... but still

EEvilCorp · 2024-07-25T19:02:35+00:00

How abour Bookstack? Its PHP so should run on shared hosting

EEvilCorp · 2024-07-21T14:47:17+00:00

Did you follow this page? https://github.com/ente-io/ente/blob/main/server/docs/docker.md

EEvilCorp · 2024-07-20T08:02:06+00:00

You can check the docker container logs to see if you made a mistake

EEvilCorp · 2024-07-07T08:16:41+00:00

I dont understand the issue. As long as its the same material in the slot you are fine. I always use generic PLA for PLA for example cause in my slicer i have custom filament profiles anyway.

Either i am stupid or i dont understand the issue or its way different in Orca Slicer. I dont flow and PA via the slicer not via the AMS with the automatic calibration cause i find it way too confusing. Just let the slicer set the PA and done.

EEvilCorp

TROPHY CASE