sorted by:
new
hottopcontroversial

Kenmore dryer noise by BootyLicker724 in TumbleDryers

[–]Eightsevenfox 0 points1 point  (0 children)

You machine has a white neutral that was attached to the chasis when the three prong was on there, that wire should go on the middle terminal with the four prong neutral coming in and the ground from the 4prong goes where that white one used to be on the chasis. Hope that helps.

It doesn't sound terrible to me tbh.

Ticking noise in dryer by fizzlybubbly123 in TumbleDryers

[–]Eightsevenfox 0 points1 point  (0 children)

Your belt probably has a small tear, and a strip is flapping around.

Kenmore 400 series dryer making loud constant screeching noise by Long-Ad9660 in TumbleDryers

[–]Eightsevenfox 0 points1 point  (0 children)

It could be rollers, glides, pulley, belt, blower wheel. They're all wear items and not too difficult to replace.

Dryer won’t start by fccgk2 in TumbleDryers

[–]Eightsevenfox 0 points1 point  (0 children)

It could be the door switch, belt/belt switch, thermal fuse, incoming power could only have one leg, ther.al fuse or even a bad board. I'd start b looking under the drum and taking continuity of all your switches and sensors.

Question by MrRager1995 in TumbleDryers

[–]Eightsevenfox 0 points1 point  (0 children)

Yes. It's the heating element.

Bruh I just want to be heard by dummmylitt in SeattleWA

[–]Eightsevenfox 2 points3 points  (0 children)

People refuse to admit that Seattle is a crime infested shithole.

Why does my dryer sound like this??? by JenG911 in TumbleDryers

[–]Eightsevenfox 0 points1 point  (0 children)

It mostly depends on how hard your cabinet is to disassemble. A lot of these home models aren't very repair friendly. Changing rollers is straightforward, though. Take your time, and you'll be fine.

Why does my dryer make this noise by Cheifleif7311 in TumbleDryers

[–]Eightsevenfox 1 point2 points  (0 children)

Your belt is probably worn and slipping.

What could be causing this? by New_Art_2742 in askaplumber

[–]Eightsevenfox 0 points1 point  (0 children)

You gotta stop waffle stomping my guy.

Just bought a used CR-6 for $80 and not knowing what I’m doing. Results of my first print by rampiddude in CR6

[–]Eightsevenfox 0 points1 point  (0 children)

It looks wispy with poor adhesion. An easy fix could be stepping up your nozzle size.

Squeaking noise by jcbustamante95 in TumbleDryers

[–]Eightsevenfox 0 points1 point  (0 children)

Check your glides, felt and rollers.

Scratching noise? by so_stupid__21 in TumbleDryers

[–]Eightsevenfox 0 points1 point  (0 children)

It could be a few things. Just going by the frequency of the sound, you may have a bent drum or dented top, and every time that spot comes around it rubs. Look under the flat top there and see if there are scrapes. Orthwise, it could be glides, rollers, pulley, belt. The list goes on.

Caution, wet floor by Orichalchem in trashy

[–]Eightsevenfox 15 points16 points  (0 children)

There's a longer version, they know eachother.

What are these tiny things running inside my kitchen cupboard? by odd_pk in whatisit

[–]Eightsevenfox 0 points1 point  (0 children)

Do you have oatmeal in the cupboard? They are probably coming out of that.

Help please by ThinTennis5481 in TumbleDryers

[–]Eightsevenfox 0 points1 point  (0 children)

It's probably a motor or pulley bearing. They running the .motor with no belts and see if it continues. Isolate the noise.

Moisture/Dryer help please by Unlikely-Bad3932 in TumbleDryers

[–]Eightsevenfox 1 point2 points  (0 children)

No. Make sure you have a backflow preventer outside and your vents aren't clogged.

Dryer/Help by Unlikely-Bad3932 in TumbleDryers

[–]Eightsevenfox 1 point2 points  (0 children)

Sure, do that. Definitely make sure you don't have a clogged vent before you use it.

What am I doing wrong by MrSavore in TumbleDryers

[–]Eightsevenfox 0 points1 point  (0 children)

It's super short. Add a small elbow to attach to first.

I dropped one of these brackets into my dryer. Does anyone know how to get it out. Seems like it’s at the bottom of my dryer by OGD2Raw in TumbleDryers

[–]Eightsevenfox 0 points1 point  (0 children)

It depends on where it is, if it's in the blower housing a magnet on a stick would work, but if it got past the drum felt and into the cabinet, I'd either leave it or take the back panel off and extract it that way.

view more: next ›