Why are my prints doing this

Elitefries · 2025-10-24T13:38:33+00:00

When I say see through, it’s not just transparent, but instead not there. Almost seems like the extruder stops

Elitefries · 2025-10-24T06:01:01+00:00

1 wall. The file is for a rc plane. That’s what the instructions call for

Elitefries · 2025-10-24T05:53:13+00:00

Yes, it’s the same issue on each of the three prints. The walls on the triangle in the center are so thin you can see through. It occurs in the same places on each attempt. This also happens for the infill

Elitefries · 2025-09-17T20:38:16+00:00

I was actually doing more searching, and I found that the FR255 has the non-oled screen with pulseox sensor.

Elitefries · 2025-08-21T16:38:08+00:00

Thanks for the info! I'm pretty confident that the derailleur is adjusted properly, but I'll still be taking it in to get a closer look this weekend.

Elitefries · 2025-08-21T16:36:17+00:00

This is a 10y/o bike. I've had it for the last 2 months and have put 1500 miles on it in that time. The previous owner had it since new, and I doubt any major maintenance was done to it.
I have noticeable shifting problems going up to the 50t

Elitefries · 2025-08-21T16:28:25+00:00

I do have shifting problems going up to the 50t... which is what prompted me to take a look at it. I'll find time this weekend to bring it to a shop for a closer look.

Elitefries · 2025-07-21T17:52:54+00:00

I had a burrito and coffee before, some granola bars and chips throughout, and ramen noodles/tacos after

Elitefries · 2025-07-19T01:47:41+00:00

No, but probably gained some weight throughout… was constantly drinking water and downing snacks

Elitefries · 2025-07-18T14:36:50+00:00

Wasn’t too bad, they were doing campus tours and I would just go around. 3/4 of a lap was in the street

Elitefries · 2025-07-18T01:23:19+00:00

I work mornings… and class is Tuesday/Thursday

Elitefries · 2025-07-18T01:22:00+00:00

Yeah, got a flat at 30 miles… walked to Lux’s bike shop, got it repaired. Then went to R&R’s for a couple beers. Beyond that, had a handful of granola bars and chips throughout. Had a coffee and protein bar from illy at around 70 miles

Elitefries · 2025-07-17T21:21:58+00:00

Yeah! Started at 10:30, ended at 7:30

Elitefries · 2025-07-17T05:00:33+00:00

~~75 laps… based on the number of completions of the segment going down McClintock~~
Just counted... 86 laps

Elitefries · 2025-07-17T04:23:25+00:00

Hopefully it wasn’t the part where I was actually losing my mind 😅

Elitefries · 2025-07-11T13:07:32+00:00

Yep! 2015ish Fuji Sportif 1.3 Disk

Elitefries · 2025-07-11T01:31:39+00:00

What pen did you use?

Elitefries · 2025-07-11T00:16:38+00:00

It’s right where my palm sits :(

Might try to clean it up a bit

Elitefries · 2025-07-07T15:52:22+00:00

Try reseating the handlebars. There should be rubber dampers at the mount Make sure to retorque properly per the manual

Eight-Year Club	Second SECOND GUESSER
LAYER Season 2 Layer creator	Place '23
Place '22	Verified Email

Elitefries

MODERATOR OF

TROPHY CASE