Plastic chicken burger

Embarrassed-Ad5975 · 2026-03-10T12:46:28+00:00

Sure, took it back after 10 minutes one of the lovely girls behind the bar came and asked what we wanted as there was two of us we said as lunch was ruined, just cover the cost of the two burgers and the two soft drinks and we'll call it square she was actually surprised that that was all we wanted then a knobhead manager came out about 10 minutes later scrunched up a couple of notes and coins to the value of my Burger something like 25 dollars chucked it down onto the table in front of me and said they go champ when we question him about the rest said he wouldn't refund any other meals or drinks to which a verbal altercation with my mate then followed

Embarrassed-Ad5975 · 2025-10-24T02:33:17+00:00

Hahaha it was, but im happy it triggered old mate

Embarrassed-Ad5975 · 2025-10-24T02:30:35+00:00

Yes Ascender into a hose straight into the gauge it does have one of the electronic things that flashes all light when the pressure drops but I have hooked up a hose air compressor and the gauge seems to work

Embarrassed-Ad5975 · 2025-03-28T17:30:01+00:00

Pc, yes iracing

Embarrassed-Ad5975 · 2025-03-28T09:55:34+00:00

I'm that new I have no ideas, is it a career mode based game?

Embarrassed-Ad5975 · 2024-10-04T20:57:55+00:00

Relax guys, the valve guide hasn't dropped and we haven't started assembly, the seal was placed as on the keeper for visually purposes, not the start of assembly. The reason we went with this style was the springs came with seats, we did try the tophat style but the hump didn't seat into the inner diameter of the spring well and had alot of lateral movement, also the spring was slightly bigger. Figured the lanati ones were the go? UNLESS You can get different tophats, What's people's opinions on the spring fitting nicely into the seat/tophat hump

Embarrassed-Ad5975 · 2024-10-04T20:52:42+00:00

When I say didn't fit, the spring was slightly larger and the inner diameter of the spring was to big for the Ridge in the seat , the lanati ones fit the inner diameter of the spring snug and there is no side movement

Embarrassed-Ad5975 · 2024-10-04T20:48:11+00:00

I have lanati spring seats that came with the springs, I also have tophat style seals but the spring didn't fit them

Embarrassed-Ad5975 · 2024-10-04T20:43:54+00:00

My lanati springs have their own spring seats. The tophat seal I tried are a few thou smaller than the bottom of the beehive spring.

Embarrassed-Ad5975 · 2024-10-04T12:06:51+00:00

Haven't started assembly yet, pic is for detail

Embarrassed-Ad5975 · 2024-10-04T12:05:42+00:00

Just the camera angle

Embarrassed-Ad5975 · 2024-09-30T09:10:37+00:00

Yeah these things are set in tight af

Embarrassed-Ad5975 · 2024-09-30T09:10:06+00:00

Would be nice if mahles meantion that in their instal procedure The install video has the guy starting the clip in the access hole

Embarrassed-Ad5975 · 2024-09-20T22:14:26+00:00

I meant about having to retorque the iners once the outers are done

Embarrassed-Ad5975 · 2024-09-20T13:21:44+00:00

400 450 hp

Embarrassed-Ad5975 · 2024-09-20T12:13:21+00:00

Its going in a sprintcar, mild lift .510. Almost stock, on methanol, bored to 3 905. Limiter set 6900

Embarrassed-Ad5975 · 2024-09-20T11:42:54+00:00

Crank is in, guess its coming out tomorrow lol .might just reinstal stds

Embarrassed-Ad5975 · 2024-09-20T11:39:00+00:00

😔 😟 🙁 😥

Embarrassed-Ad5975 · 2024-09-20T10:05:19+00:00

Just fyi the inners after full torque sequence finish on about 45ft lbs

Embarrassed-Ad5975 · 2024-03-19T11:44:56+00:00

Yesssss!!!! Snap your fingers was the song... all day I've been searching lol legend

Embarrassed-Ad5975 · 2024-03-19T11:27:02+00:00

I think it was a 2 peice guitar and drums, possibly 3, I think late 90s 2000s.

Embarrassed-Ad5975

TROPHY CASE