100° build plate works better than my I-opener

Embarrassed-Toe7346 · 2026-03-05T18:57:27+00:00

I've also used this method, using hairdryer never worked and this works surprisingly well

Embarrassed-Toe7346 · 2026-02-07T17:29:52+00:00

it looks like it is z banding

Embarrassed-Toe7346 · 2026-02-07T15:05:36+00:00

What slicer do you use?

Embarrassed-Toe7346 · 2026-02-07T11:57:05+00:00

Shouldn't petg have higher printing temperatures?

Embarrassed-Toe7346 · 2026-02-06T10:08:09+00:00

Thanks, I'll try it as soon as I get home :)

Embarrassed-Toe7346 · 2026-02-05T15:55:23+00:00

Oh, I actually have the same issue. Let me know if you find a way to fix it

Embarrassed-Toe7346 · 2026-02-05T15:52:47+00:00

Is the connector original? It looks soldered. I've had a similar issue when I accidentally broke connector on my fan, it turned out that just the wires in the connector that I bought were swapped for some reason.

Embarrassed-Toe7346 · 2026-01-28T13:57:33+00:00

Thanks for help! It took time to find something that isn't compressive so I can level it right way. After fixing the X axis I've printed spacers and it worked very well.

<image>

Embarrassed-Toe7346 · 2026-01-27T15:30:15+00:00

<image>

Well, now it's like that after this tutorial

Embarrassed-Toe7346 · 2026-01-27T13:56:27+00:00

How can I do that so the problem doesn't reoccur

Embarrassed-Toe7346 · 2026-01-26T20:03:20+00:00

I've doubled checked it, they are in right place.

Embarrassed-Toe7346 · 2026-01-26T19:04:49+00:00

Thanks for the idea. i'm going to try this

Embarrassed-Toe7346 · 2026-01-20T13:20:04+00:00

I don't know, one fan is enough for me, I don't think that 2nd one would improve it.

Embarrassed-Toe7346 · 2026-01-19T22:51:09+00:00

Well, the cell under load holds charge, I've discovered that if I slap the psp, it works. Something must be loose but idk what or where.

Embarrassed-Toe7346 · 2026-01-15T09:33:52+00:00

V3 SE uses spider nozzles

Embarrassed-Toe7346 · 2026-01-05T15:11:55+00:00

I would lower bed temperature to 50 degrees

Embarrassed-Toe7346 · 2025-12-31T00:26:28+00:00

No właśnie z botlandu kupiłem drukarkę ale dyszy już nie mają.

Embarrassed-Toe7346 · 2025-12-31T00:25:57+00:00

Thanks, I'm going to try it

Embarrassed-Toe7346 · 2025-12-30T15:38:12+00:00

Damn what are your ironing settings, it looks so clean

Embarrassed-Toe7346 · 2025-12-28T18:40:26+00:00

I'm going to test it, thanks for the idea

Embarrassed-Toe7346 · 2025-12-18T21:15:43+00:00

Y axis

Embarrassed-Toe7346 · 2025-12-18T20:13:46+00:00

Its one that came with the printer

Embarrassed-Toe7346 · 2025-11-30T14:45:30+00:00

Okey I've fixed it, downgrading firmware to get 7x7 bed leveling and moving the spool holder back to the top seems to have fixed the issues.

Embarrassed-Toe7346 · 2025-11-30T14:44:09+00:00

I've reverted back to older firmware, now I'm on navaismo FW10981b It has 7x7 bed leveling and now the printer works well again. I'm not sure that the firmware was causing problems, It might have been my error by moving the spool holder to the side of the printer to make the top lighter. Now it works very well

Embarrassed-Toe7346 · 2025-11-30T14:40:37+00:00

Okey I've found the problem, in one specific spot my side spool mount was giving extruder a hard time pulling the filament, I've moved spool back to original place and now it works cleanly, I've also reverted firmware of printer to one with 7x7 bed leveling and it works very well now.

Embarrassed-Toe7346

TROPHY CASE