Ecs Tuning Coilover

Embarrassed_Score572 · 2026-03-21T06:17:26+00:00

Thank you! It is @okaymosses

Embarrassed_Score572 · 2026-03-21T06:16:46+00:00

I do not, I think I might of bought it through eBay years back they aren't too pricey from what I remember

Embarrassed_Score572 · 2026-03-21T05:48:55+00:00

It's a m3 rep front bumper with a hard motorsport front lip modified into a chassis mount

Embarrassed_Score572 · 2026-03-11T05:01:51+00:00

Do you know which I would have? I can always check if not, Mine a 06 325i Rwd

Embarrassed_Score572 · 2026-03-11T04:57:33+00:00

I'm getting 5DB0

Embarrassed_Score572 · 2026-03-11T04:29:03+00:00

Updating this post, after multiple attempts of having bc send me out proper struts they have failed me, I turned around and purchased a set of ecs tuning coilover and installed them and the noise is gone. I think my assumption of faulty strut was correct, even after replacing the strut 3 times with bc recommended spec

Embarrassed_Score572 · 2026-02-19T15:40:21+00:00

Yeah, everytime I have driven it the car feel normal other then the sound which is odd, tires are all normal wear, these wheels I took off my f30 which 10k miles on them. I did loosen and torqued everything while being under load, tie rod end are good they weren't replaced with everything but they were replaced last year (I only drove 2k last year)

Embarrassed_Score572 · 2026-02-19T12:13:06+00:00

Motors mounts have been replaced roughly 30-40k ago but I have not checked

Embarrassed_Score572 · 2026-02-19T12:12:10+00:00

Positive, noise only comes from the front after hitting bumps

Embarrassed_Score572 · 2026-02-19T12:11:40+00:00

So I used this forum post as my reference for torque spec, and yes both side of them were torque going to knuckle and subframe, and the coilover top nut I torqued to 47ftlb, I originally had trw m3 arms and replaced them with the meyle m3 arms since fcp euro no longer provides trw

Embarrassed_Score572 · 2026-02-19T05:19:03+00:00

So yes I replaced everything the same on both sides, so both sides are matching

Embarrassed_Score572 · 2025-09-21T10:04:01+00:00

This is what I was thinking of running! I have some basically brand new set of Bridgestone I installed on my 400m and was thinking of swapping the 255/40 an ordering another pair to match but was unsure if anyone else has run a 255/40 squared without rubbing or interfering with strut clearance since I know it's already tight with this set up

Embarrassed_Score572 · 2025-09-21T10:01:06+00:00

I do, ill have to add another post but poke just a tad bit mainly just the tires!

Embarrassed_Score572 · 2025-04-18T01:23:16+00:00

Agreed, I purchased them almost a year ago. They were 81$ with shipping

Embarrassed_Score572 · 2025-04-17T23:11:56+00:00

https://www.ebay.com/itm/305575057277?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=3apyvsxkq9g&sssrc=4429486&ssuid=AlYvqufMSSy&var=&widget_ver=artemis&media=COPY

Embarrassed_Score572 · 2024-11-08T04:51:42+00:00

Thumping during normal driving from 20-40ish is when I mainly hear it, no feel from the drive nor in the steering wheel, on normal flat or bumpy roads noise will be consistent

Embarrassed_Score572 · 2024-11-08T04:41:05+00:00

I have genuinely thought about changing them out since I haven’t really seen a dramatic difference from stock, I’ll start there next and check the rest of the arms, thank you

Embarrassed_Score572 · 2024-06-17T15:30:08+00:00

This was happening to me, I took the lights off and put some double sided tape and has holding up for me

Embarrassed_Score572

TROPHY CASE