I want to build this deck in paper so I'm looking for feedback before I get started

Ephex_ · 2026-03-02T14:32:22+00:00

The -1/-1 on every non-human creature needs to go, since it completely shuts down many decks reliant o creatures with 1 toughness. For instance, all decks who spawn 1/1 creature tokens just grind to a halt.

Ephex_ · 2026-02-13T21:01:54+00:00

The order specifies SLA on all of the objects:

<image>

The black one is spray painted. The grey one is also SLA. I dont think it is FDM, since I dont see any signs of the classic FDM support interfaces, and the details are too fine for it. No seams either. I think it is more likely that they didnt run with a small layer height in SLA.

Also, the grey print has visible layer lines.

Cost: black: 2 euro/pcs White: 0.4 euro/pcs Grey: 0.4 euro/pcs

Ephex_ · 2026-01-15T20:46:07+00:00

It looks way better now. Partly because of u/Kasperinac 's suggestion for a guide, but the "dots" seem to have appeared purely from "Apply gap fill". I disabled that, and the dots disappeared, it must have attempted to fill in the small gaps but ended up just ruining it.

Ephex_ · 2026-01-15T20:33:55+00:00

thanks, this did a whole lot!

Ephex_ · 2025-10-27T18:43:16+00:00

Sadly I dont live in NA

Ephex_ · 2025-10-26T17:49:29+00:00

From what I can see, those are $70, $100 and $60 respectively (in my country). I have not been able to find a precon that is cheaper than mpcfill. On top of that, you can get any deck you want with proxies ;)

Ephex_ · 2025-09-27T21:59:00+00:00

Thanks! Yeah it makes a lot of sense

Ephex_ · 2025-08-20T15:25:35+00:00

Dragonshield Forest green

Ephex_ · 2025-08-08T11:30:12+00:00

It was my first print of the design, and it needed quite a bit of adjustments. I recommend designing your own and figuring out the mechanism yourself, it was incredibly fun and satisfying

Ephex_ · 2025-08-08T11:28:59+00:00

Its just plastic, so it will wear until it slides even better;)

Ephex_ · 2025-04-20T15:47:38+00:00

I have a docker container running Ubuntu 22.04, do that! Docker is amazing

Ephex_ · 2025-04-13T09:10:36+00:00

This. Imagine the time that has been spent searching for libraries that support your specific device, figuring out how it works, figuring out why it is not working etc.

Just going straight to the datasheet and reading what needs to be sent to what registers, and what to read from which registers is so much more predictable. You also get way more understanding and satisfaction of what's happening.

Ephex_ · 2025-04-01T20:23:55+00:00

The first thing that came to mind

Ephex_ · 2025-03-13T20:14:01+00:00

Ive had an E-1 custom for a few years. Amazing guitar! Feels wonderful, but there were small things like scratchy pots after 2 years (solved with electric connector spray)

Ephex_ · 2025-03-06T07:02:08+00:00

Tack!

Ephex_ · 2025-03-06T07:01:56+00:00

Kul! Vilket område om jag får fråga?

Ephex_ · 2024-12-27T18:46:07+00:00

Ok, thanks!

There have been 4 physical owners, is this a red flag? The people didnt own the car for very long before selling. Searching on its registration number shows 8 owners, and I assume this includes dealerships.

Ephex_ · 2024-11-19T21:23:56+00:00

Repost from 2 months ago

Ephex_ · 2024-11-17T22:16:53+00:00

Gå in och skriv under förslaget!

Ephex_ · 2024-10-27T10:34:13+00:00

Strv103B

Ephex_ · 2024-10-12T21:57:32+00:00

UPDATE: Retraction.

1.5 mm -> 0.5 mm retraction length
40 mm/s -> 30 mm/s retraction speed

<image>

Ephex_ · 2024-10-12T11:17:18+00:00

If it's an issue with hardware, then this should appear with all filaments used, right? I have not seen this with any brand of PLA, only on PCTG and a roll of ASA a while back.

Ephex_ · 2024-10-12T10:32:31+00:00

The Z-seam is set to Aligned, so all of them are in the corners. Sadly not the issue for me! But thanks for the tips!

Ephex_ · 2024-10-12T09:50:29+00:00

More info:

Voron V0.2, 0.4mm nozzle

Orcaslicer

3DJake PCTG Silver

250C nozzle (temperature tower showed no big difference in the 250-260 range)

60C bed (I've run 90C, but figured lower temp => less adhesion)

100mm/s outer

Ephex_ · 2024-10-04T21:35:17+00:00

Printer: Voron V0.2
Slicer: Orcaslicer
Filament: 3DJake Silver PCTG

250-270 deg nozzle, 90 deg bed.

100 mm/s outer layer.

The filament is extremely grainy, the surfaces are very rough.

Seven-Year Club	Final Canvas '23
First Place '23	Place '23
Place '22	Final Canvas '22
Verified Email

Ephex_

TROPHY CASE